A
747-400 MAINTENANCE MANUAL
RADIUS
ROTARY ACTUATOR FILLER HOOK POSITION
RAMP
SWITCH ACTUATOR
DOOR DOOR OPEN STOP LUG HOOK
SWITCH KEYING WASHER
HOOK POSITION SWITCH OUTBD LOCK-WASHER DOOR UP

G

SWITCH
DOOR UP SWITCH
FWD

H
PRESSURE
RELIEF DOOR
TORQUE TUBE

FWD DOOR WARNING SWITCH ADJUSTMENT

I
Cargo Door Switches
Figure 505 (Sheet 5)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-34-00
 ALL  ú ú 04 Page 521 ú Feb 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

SWITCH BRACKET
LATCH OPEN
C
C
STRIKER
MAIN LATCH  ARM
TORQUE TUBE
DOOR LATCHED SWITCH  LATCH OPEN SWITCH

C-C

Cargo Door Switches
Figure 505 (Sheet 6)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-34-00
 ALL  ú ú 06 Page 522 ú Feb 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (6)  
SSM 52-34-01, 52-35-01

 (7)  
WDM 52-34-11, 52-35-11, 52-71-01, 52-71-11

 F.  
Access

 (1)  
Location Zone 122 Forward Cargo Container Compartment, Forward Half 142 Aft Cargo Container Compartment

 (2)  
Access Panel
 821R Door - Forward Cargo Compartment
 822R Door - Aft Cargo Compartment

 G.  
Procedure

 S 865-006
 (1)  
Supply electrical power (Ref 24-22-00/201).

 S 015-007

 (2)  
Remove the lining from the cargo door, ceiling and sidewall as it is necessary (Ref 25-52-01/401).

 S 825-008

 (3)  
Adjust the master latch lock mechanism (Fig. 501):

 (a)  
Disconnect the lower ends of the two pressure relief door pushrods from the bellcranks on the torque tube.

 (b)  
Close the pressure relief doors to their faired position. 1) Make sure the pressure relief door skin is smooth with the cargo door skin +/- 0.03 inch.

 2)  Adjust the door closed stops on the two doors if it is necessary (View B-B, Fig. 501).

 (c)  
Hold the two pressure relief doors in their closed position with the clamps.

 (d)  
Close and latch the master latch lock handle.

 (e)  
For the forward cargo door, make sure the center-to-center length of the handle mechanism upper pushrod is as shown (View C-C, Fig. 501).

 (f)  
For the aft cargo door, make sure you can install the rig pin LCD-1(1) in the upper idler bellcrank of the handle mechanism.

 NOTE: If it is necessary to adjust the upper pushrod,
____
 keep the rig pin installed.

 1)  For the aft cargo door, set the lower link to a length of
 4.00 +/- 0.02 inches. This is a temporary length and may be revised, if required (Fig. 501 view C-C).
 2)  For the forward cargo door, disconnect the lower link which is attached to the lower idler bellcrank (Fig. 501 view C-C).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-34-00
 ALL  ú ú 05 Page 523 ú Feb 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
 (g)  For the aft door, make sure you can install the rig pin LCD-1(2) in the lower idler bellcrank of the handle mechanism.
 (h)  1) Adjust the lower pushrod's length if it is necessary.For the forward door, set the length of the aft lower link to 3.90 +/- 0.02 inches. 1) Insert rig pin through the aft lower idler bellcrank (Fig. 501 view C-C). 2) Adjust the forward lower pushrod to permit assembly with the forward lower idler bellcrank.
 NOTE:  The rig pin hole in the forward lower idler bellcrank should not be used.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 3(12)