+0.05
0.19 INCH
-0.00 (AT LOWER FORWARD CORNER)

+0.05
0.08 INCH
-0.00 (AT LOWER FORWARD CORNER) +0.06

0.18 INCH
-0.02

AFT DOOR SHOWN
(EXAMPLE FOR FORWARD DOOR)

AIRPLANE ON JACKS
AIRPLANE ON GEAR (DOOR SHIFTS FORWARD APPROXIMATELY 0.11 INCH AT LOWER FORWARD CORNER)
FORWARD DOOR
AFT DOOR
Cargo Door Fair Tolerances and Door Skin Gaps
Figure 406 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-34-01
 ALL  ú ú 09 Page 425 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
F81801
A
747-400
MAINTENANCE MANUAL

 CAUTION: DO NOT USE MORE THAN 25 POUND-INCHES OF TORQUE WHEN YOU
_______ TURN THE HOOK ACTUATOR IN THE RIGGED CLOSED POSITION. IF YOU USE MORE THAN 25 POUND-INCHES OF TORQUE, YOU CAN CAUSE INTERNAL DAMAGE TO THE ACTUATOR.
 (b)  Use a torque wrench with a dial indicator to manually turn the hook actuator to the rigged closed position. 1) Monitor the torque that is applied to the actuator.
 NOTE: When the torque increases by 15 pound-inches, the
____ internal stops are against each other.
 2)  Turn the actuator 2 1/2 turns manually in the opposite direction.
 NOTE: This is the rigged closed position.
____
 (c)  
Adjust the hook pin fittings to the correct flushness
 (Fig. 406).

 (d)  
Make sure the serrated plates below the fitting are correctly engaged and tightened in their position.

 (e)  
Make sure the end of the hook pin extends above the bearing housing in the limits shown in View B-B, Fig. 405.

 (f)  
If it is necessary, replace the damaged bearings, bearing housings, bearing retainer (not on all installations) or other parts, and install the pin again to get the necessary dimension.

 NOTE: An incorrect dimension can be caused by a latch pin that
____ is bumped by cargo during loading, which will cause the pin to be driven in the inward direction.
 S 824-030
 (7)  
Adjust the lower latch pin fittings as follows:

 (a)  
Make sure the hook pin fittings are correctly adjusted (Adjust hook pin fittings).

 (b)  
If dummy latch pins are not available, adjust the latch fittings as follows:

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-34-01
 ALL  ú ú 01 Page 426 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

-1 0 1 2 3  113114115116
TURNS OF MANUAL DRIVE TORQUE WRENCH
DO THESE STEPS TO FIND THE POINT WHERE THE INTERNAL STOPS ARE AGAINST EACH OTHER:
1.
 MEASURE THE NORMAL TORQUE (M) WHILE YOU MANUALLY TURN THE ACTUATOR BETWEEN STOPS. (TORQUE MUST BE CONSTANT WITHIN |2 POUND-INCHES).

2.
 FIND THE POINT AT WHICH THE TORQUE INCREASES TO 15 POUND-INCHES ABOVE THE NORMAL |2 POUND-INCHES TORQUE (M + 15) WITHIN +5/-0 POUND-INCHES.

3.
 TURN THE WRENCH 1/2-TURN IN THE OPPOSITE DIRECTION FROM (M + 15) POINT. THIS IS WHEN THE INTERNAL STOPS ARE AGAINST EACH OTHER.

Latch and Hook Actuator Internal Stop and Rig Positions
Figure 407

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-34-01
 ALL  ú ú 01 Page 427 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 CAUTION:_______DO NOT INSTALL THE PINS IN BACKWARDS. THIS WILL CAUSE DAMAGE TO THE FITTINGS, LATCH CAMS, AND ADJACENT STRUCTURE.
 MAKE SURE THAT THE PINS PROTRUDE OUT OF THE LATCH PIN FITTINGS MORE THAN 0.75 INCHES ON THE SIDE OF THE FITTING WHERE THEY ENGAGE THE LATCH CAM.
 CAUTION:_______ IN CASE THE DOOR DOES NOT OPEN, STOP IMMEDIATELY.  DO
 NOT OPERATE THE DOOR CONTROL SWITCH.  HOLDING THE
 DOOR CONTROL SWITCH MAY DAMAGE THE ACTUATOR.  WAIT AT
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 3(48)