26-22-00
ALL ú ú 10 Page 510 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 485-075
(2) Connect a multimeter between the pins 1 and 2 of the squib
electrical connector, DM103B.
S 865-066
(3) Close the circuit breaker APU START on the P83 panel.
S 035-067
(4) Remove the electrical connector, DM216A, from the fire detector,
M216, loop A, on the APU door.
S 485-068
(5) Connect a 300 to 400 ohm resistor from the center pin of the
electrical connector, DM216A, loop A, to the connector shell of the
removed fire detector element.
NOTE:____ Keep the resistor in the same location for the subsequent
steps.
S 485-070
(6)
Connect a jumper wire from the center pin of the connector DM216A, loop A, to the connector shell of the removed fire detector element.
S 735-073
(7)
Make sure 0 volts dc shows between the pins 1 and 2 on the connector DM103B.
S 865-076
(8)
Stop for 10 seconds.
S 735-077
(9)
Make sure 24 to 32 volts dc shows between the pins 1 and 2 on the connector DM103B.
S 865-134
WARNING: MAKE SURE YOU PREPARE THE AIRPLANE FOR THE AIR MODE (AMM
_______ 32-09-02/201), BEFORE YOU OPEN THE CIRCUIT BREAKERS THAT FOLLOW. FAILURE TO FOLLOW THE STEPS CORRECTLY CAN CAUSE THE AUTOMATIC OPERATION OF THE AIRPLANE SYSTEMS. THE AUTOMATIC OPERATION OF THE AIRPLANE SYSTEMS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(10)
Do this task: "Put the Air/Ground Relay System in the Air Mode" (AMM 32-09-02/201).
S 735-082
(11)
Make sure 0 volts dc shows between the pins 1 and 2 of the connector DM103B.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
26-22-00
ALL ú ú 09 Page 511 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 735-083
(12)
Stop for 10 seconds.
S 735-084
(13)
Make sure 0 volts dc shows between the pins 1 and 2 of the connector DM103B.
S 085-085
(14)
Remove the resistor and the jumper wire from the connector DM216A.
S 865-089
(15)
Do this task: Put the Air/Ground Relay System Back in the Ground Mode (AMM 32-09-02/201).
S 435-090
(16)
Install the connector DM216A into the module M216 with a torque of 50 to 70 pound-inches.
S 435-130
(17)
Install a lockwire on the connector DM216A.
S 865-093
(18)
Make sure the APU FIRE CONTROL handle is out on the fire shutdown module for the APU, M869.
S 735-094
(19)
Make sure 0 volts dc shows between the pins 1 and 2 of the connector DM103B.
S 865-095
(20)
Push the APU EXTINGUISHER DISCHARGE button on the fire shutdown module, M869, in the right wheel well.
S 735-096
(21)
Make sure 24 to 32 volts dc shows between the pins 1 and 2 of the connector DM103B.
(22)
Release the APU EXTINGUISHER DISCHARGE button.
S 865-097
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
26-22-00
ALL ú ú 08 Page 512 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
S 735-098
(23) Make sure 0 volts dc shows between the pins 1 and 2 of the connector DM103B.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 防火 FIRE PROTECTION 2(99)
