S 865-141

 (19)
 Put the toggle switch on the squib circuit test box to the OFF position.

 S 865-143

 (20)
 Turn and hold the APU fire handle fully clockwise.

 S 735-144

 (21)
 Make sure the APU BTL DISCH light on the squib circuit test box is on.

 S 975-145

 (22)
 Measure and make a record of the voltage on the multimeter (V1).

 S 865-146

 (23)
 Put the toggle switch on the squib circuit test box to the ON position.

 S 975-147

 (24)
 Make a record of the voltage on the multimeter (V2).

 S 865-148

 (25)
 Release the APU fire handle.

 (a)  Make sure the handle moves quickly to in 10 degrees or less of the center position.

 (26)
 Make sure the multimeter shows 0 | 2 volts.

 (27)
 Turn the handle to the horizontal position.

 (28)
 Push in the fire handle to the usual position.

 S 865-046

 (29)
 Put the toggle switch on the squib circuit test box to the OFF position.

 S 735-149
 S 865-150
 S 865-138
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 26-22-00
 ALL  ú ú 01 Page 508 ú Oct 10/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 015-047
 (30)
 Get access to the fire shutdown module for the APU, M869, which is installed in the right wheel well for the main landing gear.

 S 865-048

 (31)
 Pull the fire control handle on the fire shutdown module for the APU, M869.

 S 735-049

 (32)
 Make sure the APU BTL DISCH light on the squib circuit test box is off.

 S 865-050

 (33)
 Push and hold the APU EXTINGUISHER DISCHARGE button on the fire shutdown module, M869.

 S 735-051

 (34)
 Make sure the APU BTL DISCH light on the squib circuit test box is on.

 S 975-052

 (35)
 Make a record of the voltage on the multimeter (V1).

 S 865-053

 (36)
 Put the toggle switch on the squib circuit test box to the ON position.

 S 975-054

 (37)
 Make a record of the voltage on the multimeter (V2).

 S 865-055

 (38)
 Release the APU EXTINGUISHER DISCHARGE button on the M869 module.

 S 735-056

 (39)
 Make sure the multimeter shows 0 | 2 volts.

 S 735-142

 (40)
 Make sure the APU BTL DISCH light on the squib circuit test box is off.

 (41)
 Restore the APU fire control handle to its normal position.

 S 865-226

 (42)
 Open this circuit breaker on the main power distribution panel, P6, and attach a DO-NOT-CLOSE tag:

 S 865-225
 (a) 6H5, FIRE EXTINGUISHER APU
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 26-22-00
 ALL  ú ú 01 Page 509 ú Jun 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 485-057
 (43)
 Remove the squib electrical connector, DM103B, from the squib circuit test box.

 S 865-227

 (44)
 Remove the DO-NOT-CLOSE tag and close this circuit breaker on the main power distribution panel, P6:

 (a)  6H5, FIRE EXTINGUISHER APU
 S 975-058
 (45) Calculate the resistance for the squib discharge circuit, RC, with the formula that follows:
 RC = RL * (V1/V2) - RL
 Make sure the value for RC is less than 3.8 ohms.
 NOTE: If RC is more than 3.8 ohms, the circuit can not supply
____
 sufficient current to fire the squib.

 S 085-074
 (46)
 Remove the wires from the squib circuit test box.

 H.
Do a Fire Simulation Test

 S 865-220
 WARNING: DO NOT TOUCH THE SQUIB BEFORE YOU DO THE PROCEDURES FOR DEVICES
_______ THAT ARE SENSITIVE TO ELECTROSTATIC DISCHARGE. ELECTROSTATIC DISCHARGE CAN CAUSE THE FIRE BOTTLES TO RELEASE ITS CONTENTS SUDDENLY AND CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 防火 FIRE PROTECTION 2(98)