26-23-01
 ALL  ú ú 01 Page 602 ú Jun 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 216-004
 (4)  
Examine the caution and identification plates on the bottle to make sure you can read them.

 S 216-005

 (5)
Examine the hydrostatic test date shown on the inspection tag.

 D. Examine the Container Weldment
 S 226-015
 (1)  Do these steps to check the welds on the fire bottles:
 (a)  Examine the bottle weldment for scratches or dents that can decrease its strength. 1) If you find a dent with a depth more than 1/16 inch
 (1.59 mm) per inch (25.4 mm) of average dent diameter,
 replace the bottle. 2) If you find a scratch with a depth more than 0.004 inch
 (0.10 mm), replace the bottle.
 S 216-007
 WARNING: KEEP A COVER ON THE DISCHARGE OUTLET OF THE BOTTLE TO PREVENT
_______ DAMAGE TO THE CALIBRATED RUPTURE DISC. SCRATCHES OR DENTS ON THE SURFACE OF THE DISC CAN MAKE IT OPERATE INCORRECTLY. IF THE DISC IS DAMAGED THE BOTTLE CAN ACCIDENTALLY FIRE AND CAUSE INJURY TO PERSONS.
 (2)  Make sure there is no damage (cracks, breaks, or tears) on the welds.
 NOTE: Examine the welds at the mounting lugs carefully.
____
 S 216-008
 (3)  Use a strong light and magnifying glass to examine the rupture disc for damage or corrosion.
 (a)  If there is damage or corrosion on the disc, replace the discharge outlet (AMM 26-23-02/401).
 S 216-009
 (4)  Use a strong light and magnifying glass to examine the discharge outlet for damage or corrosion.
 NOTE: Ignore stains on the inner surface area of the discharge port
____
 caused by a bottle discharge.

 (a)  If there is damage or corrosion on the discharge outlet, replace the fire extinguishing bottle. (AMM 26-23-02/401).
 S 426-010
 (5) Install the fire extinguisher bottle if removed (AMM 26-23-01/401).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 26-23-01
 ALL  ú ú 01 Page 603 ú Feb 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 866-013
 (6) Close this circuit breaker on the main power distribution panel:
 (a) 6H6, FIRE EXTINGUISHER LOWER CARGO
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 26-23-01
 ALL  ú ú 01 Page 604 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 LOWER CARGO COMPARTMENT FIRE EXTINGUISHER BOTTLE
________________________________________________ DISCHARGE CARTRIDGE (SQUIB) - REMOVAL/INSTALLATION
__________________________________________________
 1.  General
_______
 A.  This procedure contains two tasks. The first task removes the discharge cartridge (squib). The second task installs the squib.
 B.  The four cargo fire bottles, M6742, M7906, M7907, and M7908 are installed aft of the forward cargo door on the right side of lower cargo compartment. There are two squibs on each fire bottle. The removal/installation procedures for all eight squibs are same.
 NOTE: If you replace the squib because it was fired or the disc is
____ damaged, you must also replace the fire extinguishing agent.
 TASK 26-23-02-004-001
 2.  Remove the Discharge Cartridge (Squib) (Fig. 401)
______________________________________
 A.  Equipment
 (1)  Squib Protective Cover
 M83723/60-208-AN or AC (Fwd Cargo)
 M83723/60-210-AN or AC (Aft Cargo)

 B.  References
 (1)  
AMM 20-41-02/201, Electrostatic Discharge Sensitive Devices

 (2)  
AIPC 26-23-01, Fig. 2

 (3)  
WDM 26-23-11, WDM 26-23-12

 C.  Access
 (1)  Location Zone 124 Forward Cargo Container Compartment Aft Half
 D.  Procedure
 S 864-062
 WARNING: DO NOT TOUCH THE SQUIB BEFORE YOU DO THE PROCEDURES FOR DEVICES
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 防火 FIRE PROTECTION 2(131)