(e)
Make sure the electrical connector is not damaged.
NOTE: If the squib electrical pins do not enter the
____ receptacles in the electrical connector, the pins can cause damage to the electrical connector.
(f)
Connect the electrical connector to the fire bottle squib.
(g)
Do the steps that follow to make sure you did not bend or damage the squib pins.
NOTE: This step is necessary because the pins are most likely
____ to be damaged the first time an electrical connector is connected to the squib.
1) Disconnect the electrical connector from the fire bottle squib. 2) Make sure the squib electrical pins are not bent or
damaged. 3) Make sure the electrical connector is not damaged. 4) Connect the electrical connector to the fire bottle squib.
F. Procedure
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
26-23-01
ALL ú ú 03 Page 409 ú Jun 10/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 864-115 WARNING: DO NOT TOUCH THE SQUIB BEFORE YOU DO THE PROCEDURES FOR DEVICES
_______ THAT ARE SENSITIVE TO ELECTROSTATIC DISCHARGE. ELECTROSTATIC DISCHARGE CAN CAUSE THE FIRE BOTTLE TO RELEASE ITS CONTENT AND
CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
WARNING:_______ MAKE SURE YOU KEEP A PROTECTIVE CAP ON THE DISCHARGE PORT. BE
CAREFUL WHEN YOU MOVE THE FIRE BOTTLE. IF THE BOTTLE IS
ACCIDENTALLY FIRED IT CAN CAUSE INJURY TO PERSONS.
(1)
Before you touch the squib, do the procedure for devices that are sensitive to electrostatic discharge (AMM 20-41-02/201).
S 034-122
(2)
Remove the protective caps, if not previously done, from the thermal relief and refill ports.
S 864-120
(3)
Before the bottle is installed, make sure its weight is not more than 0.3 pounds below the weight marked on the bottle.
NOTE: The measured weight includes the charged bottle,
____ the inspection tag attached to the bottle, and the swivel assemblies. If the squib cartridges are not installed on the fire extinguisher bottle, do not install them. Weigh the squib cartridges as loose parts. Include the weight of the squib cartridges in the measured weight. If the squib cartridges are installed, weigh the bottle with the cartridges installed. Remove all protective covers when the parts are weighed.
(a) Make sure the weight of the fire bottle is the same as the weight that shows on the bottle +/- 0.3 pound.
NOTE: Some bottles may have many bottle weights marked, make
____ sure that the last dated, marked weight is used.
S 424-011
(4)
Install the squib (8), O-ring (7), and ground lug assembly (6) into the discharge port (4) as shown in Fig. 401.
S 434-012
(5)
Torque the squib cartridge (8) to 90-100 pound-inches.
S 914-013
(6)
Use a lockwire to attach the squib cartridge (8) to the discharge port (4).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
26-23-01
ALL ú ú 01 Page 410 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(7) S 824-014Put the bottle in the correct position with the mounting lugs on the support bracket.
(8) S 434-015Install the mounting washers (11) and bolts (12) (three locations).
(9) S 824-016Loosen the gland nut (10) on the discharge head.
S 824-094
(10)
Adjust the discharge heads until the discharge ports are aligned to give the best possible hose connection.
S 434-017
(11)
Torque the gland nut (10) to 55-65 pound-feet.
S 914-019
(12) 中國航空網(wǎng) m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：747-400 AMM 飛機維護手冊 防火 FIRE PROTECTION 2(128)
