LEFT SIDE RIGHT SIDE
DE
Generator Drive System Component Location
Figure 1 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
24-11-00
ALL ú ú 02 Page 3 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
INTERMEDIATE CASE
SEE F
FWD GSEE
F
PORT OIL-OUT HEAT EXCHANGER IDG AIR/OIL CONNECTOR ELECTRICAL VALVE HEAT EXCHANGER IDG AIR/OIL
G
PORT OIL-IN Generator Drive System Component Location Figure 1 (Sheet 3)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
24-11-00
ALL ú ú 01 Page 4 ú Jun 10/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
FUEL/OIL COOLER SEE I SEE H
FWD
OIL TANK (REF)
H
ENGINE
FUEL/OIL COOLER
IDG FUEL/OIL
COOLER
FUEL-OUT
OIL-OUT
FUEL-IN
OIL-IN
I
Generator Drive System Component Location
Figure 1 (Sheet 4)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
24-11-00
ALL ú ú 01 Page 5 ú Jun 10/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
INTERMEDIATE
SEEJ
CASE
FWD
SEE K
SWITCH S1611 OVERRIDE PRESSURE EXCHANGER VALVE IDG AIR/OIL HEAT DS1611 CONNECTOR ELECTRICAL
J
OVERRIDE SOLENOID EXCHANGER VALVE IDG AIR/OIL HEAT CONTROL VALVE AND HPC SECONDARY FLOW SWITCH S1611 OVERRIDE PRESSURE EXCHANGER VALVE IDG AIR/OIL HEAT
FWD
SUPPLY TUBE
K
Generator Drive System Component Location Figure 1 (Sheet 5)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
24-11-00
ALL ú ú 01 Page 6 ú Jun 10/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
6. IDG Fuel/Oil Cooler (Fig. 1)
___________________
A. The fuel/oil cooler serves to remove heat from the IDG oil. The fuel/oil cooler consists of a tube and shell assembly in a single housing with a common fuel passage and two separate oil passages to service both the IDG oil system and the engine oil system. Hot oil flows from the oil-in port, through the shell of the cooler to the oil-out port. At the same time fuel travels from the fuel-in port, through tubes in the shell, to the fuel-out port. The fuel flow through the tubes removes the heat from oil flowing through the shell (and around the fuel tubes). The fuel/oil cooler is mounted on the high pressure compressor case (HPC) at the 9 o'clock position. For addition information on the fuel/oil cooler (AMM 79-21-00/001).
7. IDG Air/Oil Heat Exchanger Valve Override Solenoid (Fig. 1)
__________________________________________________
A. The IDG air/oil heat exchanger valve override solenoid, which is controlled by the EEC, provides pneumatic servo pressure to activate the IDG air/oil heat exchanger valve override pressure switch.
B. The solenoid is part of a common valve housing with the HPC secondary flow control valve solenoid. The solenoid is a dual coil solenoid that is energized by 28-volt dc signal from the EEC. With the solenoid energized, 15th-stage HPC muscle pressure is supplied to the IDG air/oil heat exchanger valve override pressure switch causing the switch to close. The IDG air/oil heat exchanger valve override solenoid and switch assembly are mounted on the intermediate case aft face at the 1 o'clock position.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 ELECTRICAL POWER 電源 1(9)
