EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 24-22-02
 ALL  ú ú 03 Page 405 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 D. Install the Breaker
 S 424-027
 (1)  
Install the breaker:

 (a)  
Put the breaker in position on the applicable panel.

 (b)  
Install the four screws that attach the breaker to the panel.

 (c)  
Tighten the screws.

 S 434-028
 (2)  
Connect the terminal leads to the breaker:

 (a)  
Remove the screws and terminal covers that are attached to the breaker.

 (b)  
Remove the six nuts and washers from the terminal block on the breaker.

 CAUTION:  MAKE SURE YOU CONNECT THE CORRECT TERMINAL LEAD TO EACH
_______ STUD ON THE CIRCUIT BREAKER. AN INCORRECT INSTALLATION CAN CAUSE A MALFUNCTION OF THE BREAKER AND CAUSE DAMAGE TO THE EQUIPMENT.
 (c)  
Connect the six terminal leads to the terminal block on the breaker.

 CAUTION:  INSTALL THE WASHERS BETWEEN THE TERMINAL LEADS AND THE NUTS. INCORRECT INSTALLATION CAN CAUSE HEAT THAT CAN CAUSE DAMAGE TO THE BREAKER.

 (d)  
Put a washer and a nut on terminal block.

 (e)  
Tighten the nuts to a torque of 120 | 5 pound-inches.

 (f)  
Install the terminal covers on the breaker.

 (g)  
Tighten the terminal cover screws to a torque of 8 - 11 pound-inch.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 24-22-02
 ALL  ú ú 03 Page 406 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 434-019
 (3) Connect the control cable connector to the breaker.
 ~............................................ | Equipment Number | .............................................. | Circuit Breaker | Connector | Panel | .............................................. | C951 | DC951 | P514 | | C952 | DC952 | P614 | | C953 | DC953 | P515 | | C954 | DC954 | P615 | | C955 | DC955 | P714 | | C956 | DC956 | P715 | | C957 | DC957 | P514 | | C958 | DC958 | P614 | | C959 | DC959 | P515 | | C960 | DC960 | P615 | 2.................….............…............1
 S 414-020
 (4)
Close the panel.

 S 864-021

 (5)
Remove the DO NOT OPERATE placard from the BATTERY switch.

 E.
Test the Breaker

 (1)
Supply external electrical power (Ref 24-22-00/201).

 S 864-034
 NOTE: You must connect external power to the two external power
____
 receptacles for this procedure.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 24-22-02
 ALL  ú ú 03 Page 407 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 864-035
 (2)  
Prepare for the breaker test:

 (a)  
Make sure that the ISLN lights on the four BUS TIE switches, on panel P5, are off.

 (b)  
Set the four GEN CONT switches, on the P5 panel, to ON.

 (c)  
Make sure that the FIELD OFF lights for the APU generators 1 and 2, on the P461 panel, are off.

 (d)  
Set the BATTERY switch, on the P5 panel, to ON.

 (e)  
Set the STANDBY POWER switch, on the P5 panel, to AUTO.

 S 714-030
 (3)  
If you replaced the auxiliary power breaker (APB), do a test of the APB.

 (a)  
Start the APU (Ref 49-11-00/201).

 (b)  
Let the APU operate for 90 seconds.

 (c)  
Make sure the AVAIL lights on the APU GEN 1 and 2 switches, on the P5 panel, are on.

 (d)  
Push the APU GEN 1 and 2 switches, on the P5 panel, to ON.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 ELECTRICAL POWER 電源 1(119)