(a)  
Remove the contaminated fuel/oil heat exchanger (AMM 79-21-01/401).

 (b)  
Remove the contaminated air/oil heat exchanger (AMM 24-11-14/401).

 (c)  
Replace or clean all the tubes in the IDG cooling system that connect the heat exchangers and the coolers to the IDG.

 (d)  
Install a new (clean) fuel/oil cooler (AMM 79-21-01/401).

 (e)  
Install a new (clean) air/oil heat exchanger (AMM 24-11-14/401).

 (f)  
Install a new IDG (AMM 24-11-01/401).

 TASK 24-11-01-206-014
 3.  Examine the Oil in the IDG__________________________
 A. Standard Tools and Equipment
 (1)  
Container - 2 U.S. gallon (8 liter) capacity, suitable to collect oil drainage from IDG

 (2)  
Overflow drain tool - Risbridger 2315, W & J Risbridger Ltd. Blechingley, NR. Redhill, Surrey RH1 4LN, England

 (3)  
Hydrometer

 B. References
 (1)  AMM 12-13-07/301, IDG - Servicing
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 24-11-01
 ALL  ú ú 11 Page 610 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (2)  
AMM 12-22-07/301, IDG - Servicing

 (3)  
AMM 24-11-00/501, Generator Drive System

 (4)  
AMM 24-11-04/401, Scavenge Filter

 (5)  
AMM 78-31-00/201, Thrust Reverser System

 (6)  
WDM 24-11-11, WDM 24-11-12, WDM 24-11-13, WDM 24-11-14

 (7)  
SSM 24-11-01, SSM 24-11-02, SSM 24-11-03, SSM 24-11-04

 C.  
Access

 (1)  
Location Zone
 412 Engine 1 - Main Gearbox Aft Face 6 o'clock
 422 Engine 2 - Main Gearbox Aft Face 6 o'clock
 432 Engine 3 - Main Gearbox Aft Face 6 o'clock
 442 Engine 4 - Main Gearbox Aft Face 6 o'clock

 (2)  
Access Panel
 415 Left Thrust Reverser Half - Engine 1
 425 Left Thrust Reverser Half - Engine 2
 435 Left Thrust Reverser Half - Engine 3
 445 Left Thrust Reverser Half - Engine 4

 D.  
Procedure

 S 216-008
 (1)  
Do a check of the IDG oil level.

 (a)  
Clean the oil level indicator, if it is necessary.

 (b)  
Look into the oil level indicator and align the four marks in a straight line.

 (c)  
Make sure a bright silver circle does not show in the indicator (IDG is full).

 (d)  
If the IDG has a PUSH-TO-VENT button push to button to release the internal IDG Pressure.

 (e)  
Make sure the IDG service fitting covers are not leaking.

 1)  If the covers are leaking, do the examine the IDG pressure oiler (service fitting) and pressure cap task.

 (f)  
Remove the cover from the overflow drain coupling on the IDG.

 (g)  
Put the free end of the drain hose into a container.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 24-11-01
 ALL  ú ú 12 Page 611 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 WARNING: WHEN YOU CONNECT THE OUTLET ADAPTER TO THE OVERFLOW DRAIN
_______ COUPLING, USE A RAG AROUND THE FITTING. THIS WILL PREVENT A SPRAY CAUSED BY PRESSURE IN THE IDG CASE. HOT OIL CAN CAUSE INJURIES.
 (h)  Connect the adapter and the oil drain hose to the overflow drain on the IDG.
 NOTE: When you connect the adapter to the coupling, it is
____
 usual for some oil to drain.

 (i)  
If more than 1 pint (1/2 liter) is removed from the IDG, do the examine IDG oil task (AMM 24-11-01/601).

 (j)  
If the oil removed from the IDG is less than 1 pint (1/2 liter), service the IDG (AMM 12-13-07/301).

 (k)  
If the oil level is low (silver circle appears), fill the IDG with oil (AMM 12-13-07/301).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 ELECTRICAL POWER 電源 1(40)