(a) Keep the gasket to use again, if it is not damaged.
TASK 71-11-08-404-005-C00
3. Install the Vortex Control Device (Fig. 401)
_________________________________
A. Equipment
(1) Heat gun
NOTE: The heat gun is used if the mating
____
surfaces are below 50°F (10°C).
B. Consumable Materials
(1) Solvent - Dowclene EC (Ref 70-10-01)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-11-08
ALL ú ú C01 Page 401 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
SCREW
GASKET
FAN COWL
COLLAR
FAN COWL PANEL WITHOUT VCD INSTALLED
A
Vortex Control Device (VCD) Installation
Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-11-08
ALL ú ú C02 Page 402 ú Oct 25/85
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(2)
Coating, Vinyl - Green Strippable (Ref 70-10-01)
(3)
Sealant - BMS 5-95 (Ref 70-10-01)
C.
References
(1)
20-10-27/201, Heat Guns
(2)
71-11-02/201, Fan Cowl Panels
D.
Access
(1)
Location Zones
506 Engine No. 1 - Inboard Fan Cowl Panel
606 Engine No. 2 - Inboard Fan Cowl Panel
(2)
Access Panels
5737 Engine No. 1 - Fan Cowl Panel
5846 Engine No. 2 - Fan Cowl Panel
E.
Procedure
S 164-017-C00
CAUTION:_______INSTALL THE VCD ONLY ON THE INBOARD FAN COWL PANEL. THE
INCORRECT INSTALLATION OF THE FAN COWL VCD CAN CAUSE
UNSATISFACTORY AIRPLANE PERFORMANCE.
(1) Remove the used sealant from the gasket, VCD, screw heads, and
washers.
(a) Replace the gasket if it is necessary.
S 034-008-C00
(2)
If it is necessary, remove the 16 screws, washers, and collars from
the fastener holes in the fan cowl panel.
S 114-009-C00
(3)
Clean the mating surfaces of the VCD and fan cowl panel with solvent and wipe dry.
S 884-010-C00
(4)
If the temperature of the mating surfaces is below 50°F (10°C),
use a heat gun to increase the temperature.
(a) Do not use warm air that is more than 120°F [50°C] on the structure.
(5)
Apply the vinyl coating to the mating area of the fan cowl panel.
(6)
Apply the sealant to the two sides of the gasket.
S 424-013-C00
(7)
Put the gasket and VCD on the inboard fan cowl panel and align the
fastener holes.
S 394-011-C00
S 394-012-C00
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-11-08
ALL ú ú C02 Page 403 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 034-014-C00
(8)
Install the 16 countersunk screws, washers, and new collars.
S 394-015-C00
(9)
Apply a bead of the sealant around the bottom of the VCD and on the collars and washers.
(a)
Apply the sealant on the heads of the screws and make a continuous surface.
(b)
Remove the unwanted sealant to get a smooth surface
(tack free time is 10 hours).
(c)
Permit the sealant to cure for 20 hours
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 動力裝置 POWER PLANT 2(146)
