LATCH NO. 1
NO. 4
LATCH
NO. 2
NO. 3
FOR GAP ADJUSTMENT

B-B
Fan Cowl Panel Lower Latch Adjustment Figure 501 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-11-03
 ALL  ú ú C01 Page 502 ú Oct 25/85
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////

E-E
Fan Cowl Panel Lower Latch Adjustment Figure 501 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-11-03
 ALL  ú ú C01 Page 503 ú Feb 25/87
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(2)  
Compound - Sealing,
 (optional to the synthetic rubber cement)
 Buna-N, MIL-S-4383 (Ref 70-10-01)

 (3)  
Methyl Ethyl Keytone (MEK) (Ref 70-10-01)

 D.
Access

 (1)  
Location Zones
 506 Engine No. 1 - Fan Frame
 606 Engine No. 2 - Fan Frame

 (2)  
Access Panels
 5746/5846 Fan Cowl Panel (LH)
 5737/5837 Fan Cowl Panel (RH)

 E.
Gap Adjustment

 S 415-002-C00
 CAUTION: DO NOT USE MORE THAN 60 POUNDS (270 NEWTONS) OF FORCE TO PUSH
_______ THE LATCH HANDLE CLOSED. TOO MUCH FORCE CAN CAUSE DAMAGE TO THE LATCH.
 (1)  
Make sure the thrust reverser is closed and latched.

 S 415-003-C00

 (2)  
Close the fan cowl panels (Ref 71-11-02/201).

 (a)  
Do not engage the latch No. 2 and latch No. 3.

 S 225-004-C00
 (3)  
Measure the clearance between the left and right fan cowl panel skins at each latch location.

 (a)
The clearance must be between 0.06 inches (1.5 mm) and

 0.40 inches (10.2 mm).
 S 825-005-C00
 (4)  
If the clearance is not in the limits, add or remove shims from the latch and latch keeper fittings to get the correct clearance.

 S 435-006-C00

 (5)  
If it is necessary to install shims, do these steps to install the shims:

 NOTE: It is necessary to symmetrically install shims (latch and
____ latch keeper) on the latch housing to prevent distortion.
 (a)  For the shim locations on the left fan cowl panel at the latch fittings (6 places), do these steps: 1) Clean the mating surface of the latch fitting with MEK. 2) Dry the mating surface with a clean dry cloth.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-11-03
 ALL  ú ú C01 Page 504 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
3)  If you use BMS 5-14 cement, mix the cement, 50% by volume, with MEK, 50% by volume.
 NOTE: It is not necessary to mix MIL-S-4383 sealing
____
 compound.

 4) Apply the cement mixture or sealing compound to the shim and latch fitting mating surfaces. 5) Let the adhesive to dry for 10 minutes, or until the surface is tacky, but does not move when you touch it. 6) Install the shim with a screw, nut, and washer. a) Tighten the nut.
 (b)  For the shim locations on the right fan cowl panel at the latch keeper fittings (2 places), do these steps: 1) Remove the nut and washer that attach the shear pin to the
 latch keeper fitting. 2) Clean the mating surface of the latch keeper fitting with
 MEK. 3) Dry the mating surface with a clean dry cloth. 4) Apply the cement mixture or sealing compound to the mating
 surfaces of the shim and latch keeper fitting. 5) Let the adhesive to dry for 10 minutes, or until the surface is tacky, but does not move when you touch it. 6) Install the shim on the shear pin with the nut and washer. a) Tighten the nut.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 動力裝置 POWER PLANT 2(136)