(b)  
Turn the screwdriver handle 90 degrees clockwise to release the latches.

 (c)  
Open the door.

 S 482-043-C00
 (2)  Install the load test adapter (Fig. 201).
 (a)  
Remove the two latch screws, washers and nuts near the latch bolt (nearest to the door edge).

 (b)  
Attach the adapter to the door with the two cap screws and nuts supplied with the adapter. 1) Use the two holes where you removed the latch screws.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-11-05
 ALL  ú ú C01 Page 201 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
LATCH 0.03-0.09 INCH HANDLE (0.76-2.3 mm) BLATCH HANDLE SLOT
0.06-0.09 INCH (1.5-2.3 mm)
ROLL PIN
HOLESSEE A 0.01-0.07 INCH
(0.25-1.8 mm) 0.03-0.09 INCH (0.76-2.3 mm)
DOOR FRAME (REF)
DOOR
AA
LATCH
(REF)
B
0.03-0.09 INCH (0.76-2.3 mm)
FWD
A
INSTALL BOLT AND NUT FINGER BOLT
TIGHT SPRING SCALE (REF)
LATCH LOAD ADAPTER ASSEMBLY DOWN
NOTE: DOOR LATCH/DOOR SHOWN IN OPEN POSITION.
|0.03 INCH 
90`  DOOR  (|0.76 mm)  FAN COWL 
SCREW  PANEL 

(4 LOCATIONS)
DOUBLER
SHIM

LATCH
PLATE
WASHER RUBBER PAD
(4 LOCATIONS) NUT LATCH SCREW, WASHER
(4 LOCATIONS)
(LATCH RELEASED) (LATCH SECURED) A-A A-A
Oil Tank Access/Pressure Relief Door Installation
Figure 201 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-11-05
 ALL  ú ú C01 Page 202 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////

ANGLE
| 0.025 INCH (| 0.635 MM)
FILLER SHIM
SCREW

Oil Tank Access/Pressure Relief Door Installation
Figure 201 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-11-05
 ALL  ú ú C01 Page 203 ú Jun 25/85
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
2) Tighten the nut with your fingers.
 S 412-044-C00
 (3)  
Do these steps to close the access door.

 (a)  
Put a screwdriver blade into the latch slots.

 (b)  
Turn the screwdriver handle clockwise until the latches are in the fully open position.

 (c)  
Close the access door.

 (d)  
Turn the screwdriver handle 90 degrees counterclockwise to lock the latch with the installed adapter.

 (e)  
Do not lock the opposite latch.

 S 722-045-C00
 (4)  
Do the latch release test as follows:

 (a)  
Attach a spring scale to the load test adapter.

 (b)  
Pull the spring scale straight out from the door.

 (c)  
Make a record of the force to release the latch.

 (d)  
Make sure the measured force is 47-65 pounds (210-290 newtons).

 (e)  
If the release force is not in the limits, replace the latch.

 (f)  
Remove the spring scale and adapter.

 (g)  
Install the two latch mounting screws, washers and nuts.

 S 722-046-C00
 (5)  
Do the test on the opposite latch.

 S 412-047-C00

 (6)  
Close the access door and lock the latches.

 TASK 71-11-05-902-006-C00
 3.  The Latch Removal/Installation Procedure (Fig. 201)________________________________________
 A. Consumable Materials
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 動力裝置 POWER PLANT 2(142)