(2)
AMM 12-31-91/201, Nacelle and Engine-To-Fairing Access Doors and Panels
(3)
AMM 24-22-00/201, Manual Control
(4)
AMM 78-31-00/201, Thrust Reverser System
D. Access
(1) Location Zone (AMM 12-31-01/201) 505 Left Nacelle - Right Half Thrust Reverser 507 Left Nacelle - Left Strut Area 605 Right Nacelle - Right Half Thrust Reverser 607 Right Nacelle - Right Strut Area
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
36-11-05
ALL ú ú 04 Page 516 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(2) Access Panels (AMM 12-31-91/201)
5731 Left Engine, Access Panel Strut
5737 Left Engine, Right Half Fan Cowl Assembly
5738 Left Engine, Left Half Thrust Reverser Assembly
5739 Left Engine, Right Half Thrust Reverser Assembly
5746 Left Engine, Left Half Fan Cowl Assembly
5831 Right Engine, Access Panel Strut
5837 Right Engine, Right Half Fan Cowl Assembly
5838 Right Engine, Left Half Thrust Reverser Assembly
5839 Right Engine, Right Half Thrust Reverser Assembly
5846 Right Engine, Left Half Fan Cowl Assembly
E. Prepare To Do The System Test
S 865-162
(1)
Supply electrical power (AMM 24-22-00/201).
S 015-096
(2)
Open the fan cowl panels (AMM 71-11-04/201).
S 015-097
WARNING: OBEY THE INSTRUCTIONS IN THE PROCEDURE TO OPEN THE THRUST
_______ REVERSERS. IF YOU DO NOT OBEY THE INSTRUCTIONS WHEN YOU OPEN THE THRUST REVERSERS, INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR.
(3)
Open the thrust reversers (AMM 78-31-00/201).
S 015-098
(4)
Remove the applicable access panel for the strut.
F. Do the System Test
S 865-074
(1) Push the BLEED TRIP OFF lights on the P5-10 panel.
(a)
Make sure the two BLEED TRIP OFF lights come on when you push them.
(b)
Make sure the two BLEED TRIP OFF lights go off when you release them.
S 865-163
(2) Disconnect these electrical connectors when it is necessary:
(a)
D526 - Engine No. 1 Bleed Air Overheat Switch
(b)
D528 - Engine No. 2 Bleed Air Overheat Switch
(c)
D3064 - Engine No. 1 and Engine No. 2 Bleed Air Regulator (regulator)
S 215-076
(3) Do the steps that follow to examine one of the bleed air control system:
(a) Put the 1 BLEED switch to the ON position.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
36-11-05
ALL ú ú 01 Page 517 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(b) Measure the voltage between the pins 5 and 6 at the electrical connector for the bleed air regulator. 1) Make sure the voltage is 28 | 5 VDC.
CAUTION: PNEUMATIC SYSTEM PRESSURE MUST BE REMOVED BEFORE THE
_______ ENGINE START VALVE IS MANUALLY OPENED. PRESSURE IN THE PNEUMATIC SYSTEM CAN CAUSE DAMAGE TO EQUIPMENT.
(c)
Remove the pressure from the pneumatic system (AMM 36-05-00/201).
(d)
Use a wrench to manually open and hold the Engine Start Valve to approximately 30 degrees in the open position.
(e)
Measure the voltages between these pins at the electrical connector for the regulator: 1) Pins 5 and 6 measure 0 | 2 VDC. 2) Pins 6 and 7 measure 28 | 5 VDC.
(f)
Release the Engine Start Valve.
(g)
Measure the voltages between these pins at the regulator connector: 1) Pins 5 and 6 measure 28 | 5 VDC. 2) Pins 6 and 7 measure 0 | 2 VDC.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機(jī)維護(hù)手冊 PNEUMATIC(42)
