曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 S 434-024
 (5)  If it is applicable, tighten the duct support clamps.
 NOTE:____ For the 0.016 inch titanium ducts on the TAI system support clamps the torque is 10-15 pound-inches or 10 pound-inches more than the nut threading torque. Use the Torque which is the largest.
 (a)  If you removed the support clamps to align the V-band clamps, do the step that follows: 1) Move the assembled tubing sufficiently to engage the support clamps in a way that they will not damage the tubing. 2) Do not loosen the V-band clamp to align the support clamps.
 S 434-021
 (6)  If it is applicable, tighten the support links which are attached to the duct.
 S 864-025
 (7)  Remove the DO-NOT-OPERATE tags from the switches that follow: (a) The BLEED switches. (b) The start lever. (c) The forward thrust lever.
 S 864-022
 (8)  Pressurize the pneumatic system (AMM 36-05-00/201). (a) Examine the repaired joints for leakage. 1) Diffused leakage is permitted, jet blast leakage must be repaired.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 36-19-15
 ALL  ú ú 02 Page 407 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 C. Put the Airplane to Its Usual Condition
 S 864-023
 (1)
Remove the pressure from the pneumatic system (AMM 36-05-00/201).

 S 414-029

 (2)  
Do the necessary steps that follow to put the airplane back to its usual condition:

 WARNING: OBEY THE INSTRUCTIONS IN THE PROCEDURE TO CLOSE THE THRUST
_______ REVERSERS. IF YOU DO NOT OBEY THE INSTRUCTIONS WHEN YOU CLOSE THE THRUST REVERSERS, INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR.
 (a)  
Close the thrust reversers (AMM 78-31-00/201).

 (b)  
Close the fan cowl panels (AMM 71-11-04/201).

 (c)  
Do the activation procedure for the thrust reverser (AMM 78-31-00/201).

 (d)  
Install the access panels.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 36-19-15
 ALL  ú ú 01 Page 408 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 PNEUMATIC DUCT - ADJUSTMENT/TEST
________________________________
 1.  General
_______
 A.  This procedure contains two tasks. The first task examines the APU supply duct for interference condition with the access cutout at the aft pressure bulkhead. The second task performs the adjustment to the APU supply duct to get more clearance at the access cutout to remove the interference condition.
 B.  It should be noted that this area of concern is very difficult to access. The adjustment procedure may require the removal of a lavatory or galley compartment in the aft passenger cabin area in order to get access to the duct interference area through the floor panels. Adjustments should only be made if an interference condition is believed to exist between the APU supply duct and the aft pressure bulkhead.
 C.  Do the adjustment procedure only if there are no other discrepencies found to have caused the interference condition.
 D.  If the completion of this procedure still does not provide sufficent clearance to resolve the interference condition, refer to Boeing In-Service Activity Report (ISAR) No. 92-23-3611-14, dated 14 Dec 1992 for additional steps that can be taken to resolve the interference condition.
 TASK 36-19-15-205-013
 2.  APU Supply Duct Interference Inspection (Fig. 501)
_______________________________________
 A.  References
 (1)  
AMM 12-31-41/201, Body Section 48 Access Doors and Panels

 (2)  
AMM 36-19-15/401, Pneumatic Ducts

 B.  Access
 (1)  
Location Zones (AMM 12-31-01/201)
 701 Tail Compartment

 (2)  
Access Panels (AMM 12-31-41/201)
 3701L Stabilizer Trim Access Door

 

 C.  Procedure
 S 415-028
 (1)  
Open the stabilizer trim access door, 3701L at the tail compartment (AMM 12-31-41/201).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 PNEUMATIC(111)