C. Access
 (1)  Location Zone
 215 Keel Beam

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 29-15-81
 ALL  ú ú 01 Page 204 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 D. Procedure
 S 212-017
 CAUTION: MAKE SURE THAT UNWANTED MATERIAL DOES NOT GO INTO THE MODULE
_______ HOUSING OR THE HYDRAULIC LINES DURING THE INSTALLATION. THIS CAN CAUSE DAMAGE TO EQUIPMENT.
 (1)  
Make sure unwanted material does not go into the module housing or the hydraulic lines.

 S 432-018

 (2)  
Install the O-rings and the unions in the module unit ports.

 S 642-019

 (3)  
Apply assembly lube or hydraulic fluid to the O-rings and the threads of the unions and the reducers.

 S 212-020

 (4)  
Make sure the check valve is installed in port 4.

 S 212-021

 (5)  
Make sure a plug is installed on port 5 with a lockwire.

 S 422-022

 (6)  
Put the standby pressure module in its mounting position.

 S 422-023

 (7)  
Install the bolts.

 S 032-024

 (8)  
Remove the plugs from the hydraulic lines.

 S 432-025

 (9)  
Connect the hydraulic lines to the port fittings.

 S 432-028

 (10)
 Connect the electrical connectors to the leading edge flap standby drive shutoff valve, the low pressure switch and the standby rudder actuator shutoff valve.

 S 862-029

 (11)
 Remove the DO-NOT-CLOSE tags and close these circuit breakers:

 (a)  
P6-2 Circuit Breaker Panel
 1) FLIGHT CONTROL SHUTOFF VALVES STBY RUD

 (b)  
P6-11 Circuit Breaker Panel
 1) STBY HYD PUMP NORMAL

 (c)  
P6-12 Circuit Breaker Panel
 1) STBY HYD PUMP (ALT)

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 29-15-81
 ALL  ú ú 01 Page 205 ú Jul 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 862-030
 (12)
 Pressurize the system B and the standby hydraulic reservoirs (Ref 29-09-00/201).

 S 862-031

 (13)
 Supply electrical power (Ref 24-22-00/201).

 S 862-032

 (14)
 Pressurize the standby hydraulic system.

 (a)  
Put the FLT CONTROL A switch or the FLT CONTROL B switch, on the P5 panel, to STDBY RUD.

 (b)  
Put the ALTERNATE FLAPS arm switch, on the P5 panel, to ARM.

 WARNING:_______ MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE RUDDER
 AND THE LEADING EDGE FLAPS AND SLATS BEFORE PRESSURIZATION.
 THE RUDDER AND THE LEADING EDGE FLAPS AND SLATS CAN MOVE
 QUICKLY.  THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO
 EQUIPMENT.

 S 862-041
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE RUDDER,
_______ THE LEADING EDGE FLAPS AND THE SLATS BEFORE OPERATION. THE RUDDER, THE LEADING EDGE FLAPS AND THE SLATS CAN MOVE QUICKLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (15) Operate the leading edge flaps and slats and the rudder.
 (a)  
Operate the rudder to full travel slowly a minimum of three times.

 (b)  
Put the FLT CONTROL switch used to ON.

 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE
_______ TRAILING EDGE (TE) FLAPS AND THE LEADING EDGE (LE) FLAPS AND SLATS BEFORE YOU OPERATE THE ALTERNATE FLAPS CONTROL SWITCH. THE TE FLAPS CAN MOVE QUICKLY. THE LE FLAPS AND SLATS CAN MOVE MORE QUICKLY THAN THE TE FLAPS. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (c)  
Put the ALTERNATE FLAPS control switch to DOWN.

 (d)  
Put the ALTERNATE FLAPS control switch to OFF when the trailing edge flaps are extended to 10 degrees.

 (e)  
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 液壓 HYDRAULIC POWER(121)