C. Procedure
 S 414-004
 (1)  Do these steps to install the module:
 (a)  
Remove the protective covers from the electrical connectors.

 (b)  
Examine the electrical connectors for bent or broken pins, dirt and damage. 1) Clean or repair the electrical connectors if it is

 necessary.

 (c)  
Connect the electrical connectors to the electrical module assembly.

 CAUTION:_______CAREFULLY INSTALL THE MODULE INTO THE OVERHEAD PANEL. IF YOU DO NOT, DAMAGE TO THE ELECTRICAL CABLES AT THE REAR OF THE MODULE CAN OCCUR.

 (d)  
Put the module carefully into position in the overhead panel.

 (e)  
Tighten the quarter turn fasteners on the module.

 D. Installation Test of the AC System Generator and APU Module
 S 764-005
 (1)  Do this task:
 (a)  AC Generation System test (AMM 24-21-00/501).
 E. Put the Airplane Back to its Usual Condition
 S 864-009
 (1) Remove electrical power, if it is not necessary (AMM 24-22-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 24-21-51
 ALL  ú ú 01 Page 402 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 GENERATOR DRIVE AND STANDBY POWER MODULE (P5-5) - REMOVAL/INSTALLATION
______________________________________________________________________
 1.  General_______
 A.  This procedure has these tasks:
 (1)  
Removal of the Generator Drive and Standby Power Module

 (2)  
Installation of the Generator Drive and Standby Power Module

 B.  
The Generator Drive and Standby Power Module, P5-5, is located on the P5 Overhead Panel in the flight compartment.

 TASK 24-21-52-004-001
 2.  Removal of the Generator Drive and Standby Power Module_______________________________________________________
 A.  References
 (1)  
AMM 24-22-00/201, Electrical Power

 B.  
Access

 (1)  
Location Zone
 211 Flight Compartment, Left

 C.  
Prepare for the Removal

 S 864-007
 (1)
Remove electrical power from the airplane (AMM 24-22-00/201).

 D.  
Procedure

 S 014-002
 (1)  Do these steps to remove the module:
 (a) Loosen the quarter turn fasteners on the module.
 NOTE: Hold the module when you loosen the quarter turn
____ fasteners so that the module does not fall.
 CAUTION:_______CAREFULLY REMOVE THE MODULE FROM THE OVERHEAD PANEL. IF YOU DO NOT, DAMAGE TO THE ELECTRICAL CABLES AT THE REAR OF THE MODULE CAN OCCUR.
 (b)  
Pull the module carefully out from the overhead panel to get access to the electrical connectors.

 (c)  
Disconnect the electrical connectors from the module.

 (d)  
Put protective covers on the electrical connectors.

 TASK 24-21-52-404-003
 3.  Installation of the Generator Drive and Standby Power Module____________________________________________________________
 A.  References
 (1)  
AMM 24-22-00/201, Remove Electrical Power

 (2)  
AMM 24-54-00/501, Standby Power System.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 24-21-52
 ALL  ú ú 01 Page 401 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 B. Access
 (1)  Location Zone
 211 Flight Compartment, Left

 C. Procedure
 S 414-004
 (1)  Do these steps to install the module:
 (a)  
Remove the protective covers from the electrical connectors.

 (b)  
Examine the electrical connectors for bent or broken pins, dirt and damage. 1) Clean or repair the electrical connectors if it is

 necessary.

 (c)  
Connect the electrical connectors to the electrical module assembly.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 電源 ELECTRICAL POWER(118)