(b)  
Momentarily set the GEN 1 switch (for engine No. 1) or the GEN 2 switch (for engine No. 2) on the P5 panel to ON.

 (c)  
Make sure that the applicable GEN OFF BUS light goes off.

 (d)  
Make sure the AC voltmeter shows 115 | 5 volts and the FREQ meter shows 400 | 5 Hz.

 (e)  
Momentarily set the GEN 1 (or 2) switch to OFF.

 (f)  
Push and hold the RESID VOLTS button.

 (g)  
Make sure the AC voltmeter shows 10 - 21 volts.

 (h)  
Release the RESID VOLTS button.

 G.
Put the Airplane Back in its Usual Condition

 (1)  
Shutdown the engine (AMM 71-00-00/201).

 S 864-034
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. CONSTANT SPEED DRIVES ú

 24-21-11
 ú ú 02 Page 409 ú Mar 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 414-021
 (2) Close the fan cowl panel (AMM 71-11-02/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. CONSTANT SPEED DRIVES ú

 24-21-11
 ú ú 02 Page 410 ú Mar 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 APU GENERATOR - REMOVAL/INSTALLATION
____________________________________
 1.  General
_______
 A.  This procedure contains four tasks for the APU generator.
 (1)
The removal of the APU ac generator with the APU installed.

 (2)
The installation of the APU ac generator with the APU installed.

 (3)
The removal of the APU ac generator with the APU removed.

 (4)
The installation of the APU ac generator with the APU removed.

 B.  
You can remove the generator with the APU installed, but the generator removal is easier with the APU removed.

 C.  
The installation of the APU generator is different from the installation of the engine-driven generator.

 (1)  
The APU generator has a duct support bracket assembly which is installed on the exciter end cover with six screws.

 (a)  The support bracket has two extended holes to hold the current transformer mount assembly.

 (2)  
Use the nut plates with all the bolts for the current transformer and the mount installation.

 TASK 24-21-21-004-001
 2.  The Removal of the APU AC Generator (APU Installed) (Fig. 401)
___________________________________________________
 A.  References
 (1) AMM 20-30-21/201, Lubricants ú (2) AMM 20-30-51/201, Miscellaneous Materials
 B.  Access
 (1)  
Location Zone
 303 APU Compartment

 (2)  
Access Panel
 3804 APU Cowl Door

 C.  
Procedure

 S 014-002
 (1)  Open the access door 3804.
 (a)  Install the door support rods.
 S 014-092
 CAUTION:_______BE CAREFUL WHEN YOU TOUCH THE SHROUD. DAMAGE TO THE SHROUD DRAIN LINES CAN OCCUR, IF YOU DO NOT CORRECTLY HOLD THE SHROUD.
 (2)  Remove the shroud.
 (a)  
Use support for the lower shroud.

 (b)  
Open the shroud latches.

 (c)  
Remove the shroud.

 S 034-004
 (3)  Remove the electrical connectors.
 (a)  Disconnect the electrical connectors (4 each) from the right forward side of the APU higher shroud.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 24-21-21
 ALL  ú ú 01.1 Page 401 ú Jul 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (b)  Disconnect the wires for the APU starter (2 each) at the
 starter.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 電源 ELECTRICAL POWER(104)