AFDS AIL FORCE LIM 5) AUTO FLT CONT SYS A SNSR EXC AC 6) AUTO FLT CONT SYS A FCC DC 7) AUTO FLT CONT SYS A ENGAGE INTLK A 8) AUTO FLT CONT SYS A WARN LIGHT BAT
S 494-041
WARNING: YOU MUST CAREFULLY INSTALL THE GROUND LOCKS ON ALL LANDING
_______ GEAR. AN ACCIDENTAL RETRACTION OF THE LANDING GEAR CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(3) Make sure that you install the gear ground lock assemblies
(Ref 32-00-01/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
22-11-25
ALL ú ú 01 Page 405 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 014-014
(4) Make sure that you open the screen doors (if installed) for tire burst protection purpose in the left main wheel well.
E. Procedure
S 434-015
(1) Lightly lubricate the new O-ring on the reducer and the union with hydraulic fluid. Install the reducer and the union in the ports on the actuator.
NOTE: Install the reducer in the pressure port of the actuator.
____
S 614-016
(2)
Make sure that you fill the actuator with hydraulic fluid. Seal the reducer and the union with plugs.
S 424-033
(3)
Hold the actuator in position and install the mounting bolts, washers, and nuts.
NOTE: Make sure that the countersunk side of the washer is against
____
the head of the bolt.
S 434-019
(4) Place the lever assembly on the actuator and carefully align the splines.
NOTE: The position of a tooth not on the spline provides the
____
access.
S 434-044
(5)
If you removed the lever assembly from the rod assembly then install the bolt(s), washer(s), and nut(s), that attach the lever assembly to the rod assemblies.
S 434-020
(6)
Install the clamp-bolt, washer, and nut to attach the lever assembly to the actuator, then install the washer and nut on the output shaft of the actuator. Tighten the nut on the output shaft, and then tighten the clamp-bolt.
S 434-021
(7)
Remove the plugs from the hydraulic lines and the plugs on the reducer and the union. Connect the hydraulic lines to the hydraulic ports on the actuator.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
22-11-25
ALL ú ú 03 Page 406 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 434-022
(8)
Remove the plug from the hydraulic port on the actuator. Install the hydraulic pressure switch on the actuator.
S 434-023
(9)
Connect the electrical connectors to the actuator and the hydraulic pressure switch.
S 794-024
(10)
Do a check of the actuator for hydraulic leak.
(a)
Supply the electrical power (Ref 24-22-00/201).
(b)
Supply the hydraulic power (Ref 29-15-00/201).
WARNING: MAKE SURE THAT YOU MOVE PERSONS AND BLOCKAGES AWAY FROM
_______ THE AILERONS, RUDDER, ELEVATORS, AND TABS. THESE SURFACES MAY MOVE WHEN YOU APPLY THE HYDRAULIC POWER. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(c)
Supply the hydraulic pressure to the aileron hydraulic systems A and B (Ref 27-11-00/201).
(d)
Visually examine the actuator and make sure that there is no hydraulic leak.
S 824-025
(11)
Adjust the autopilot aileron actuator (AMM 22-11-25/501).
S 724-026
(12)
Do the autopilot aileron actuator test (AMM 22-11-25/501).
F. Put the Airplane Back to Its Initial Condition
S 414-027
(1)
Install the screen doors (if removed) for tire burst protection purpose in the left main wheel well.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 自動飛行 AUTOFLIGHT 1(171)
