S 825-022

 (13)
 Adjust the position transmitter of the air mix valve if the indicator needle of the AIR MIX VALVE indicator did not align with the inner marks at COLD and HOT (Ref 21-61-71/501).

 G. Manual Mode Test - Temperature Control System (Passenger Cabin)
 S 035-023
 (1)  
Disconnect the electrical connector, D490, from the right pack valve.

 S 865-024

 (2)  
Move the R PACK switch to AUTO or HIGH, on the P5-10 panel.

 S 865-025

 (3)  
Move the PASS CABIN temperature selector switch to MANUAL OFF, on the P5-17 panel.

 S 215-026

 (4)  
Make sure the indicator needle of the PASS CABIN - AIR MIX VALVE indicator aligns with the inner mark at COLD, on the P5-17 panel.

 NOTE: This will show that the air mix valve is in the full cold
____
 position.

 (a)  Adjust the position transmitter of the right air mix valve if the indicator needle does not align with the inner mark at COLD (Ref 21-61-71/501).
 S 215-027
 (5)  
Make sure the position of the visual indicator on the air mix valve agrees with the PASS CABIN - AIR MIX VALVE indicator.

 (6)
Move the PASS CABIN temperature selector switch to MANUAL WARM.

 S 865-028
 NOTE: This will cause the air mix valve to move toward the full hot
____
 position.

 S 215-029
 (7)  Make sure that the indicator needle of the PASS CABIN - AIR MIX VALVE indicator moves to the inner mark at HOT.
 NOTE: This will show that the air mix valve is in the full hot
____
 position.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-61-00
 ALL  ú ú 01 Page 505 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 865-030
 (8) Move the PASS CABIN temperature selector switch to MANUAL COOL.
 NOTE: This will cause the air mix valve to move toward the full
____
 cold position.

 S 215-031
 (9)  Make sure that the indicator needle of the PASS CABIN - AIR MIX VALVE indicator moves to the inner mark at COLD.
 NOTE: This will show that the air mix valve is in the full cold
____
 position.

 S 865-032
 (10)
 Move the PASS CABIN temperature selector switch to MANUAL OFF.

 S 865-033

 (11)
 Move the R PACK switch to OFF.

 S 435-034

 (12)
 Connect the electrical connector, D490, to the right pack valve.

 S 825-035

 (13)
 Adjust the position transmitter of the air mix valve if the indicator needle of the AIR MIX VALVE indicator did not align with the inner marks at COLD and HOT (Ref 21-61-71/501).

 H. Automatic Mode Test - Temperature Control System (Control Cabin)
 S 715-193
 CAUTION: DO NOT USE AN OHMMETER FOR A CONTINUITY CHECK OF THE
_______ TEMPERATURE SENSORS DURING THE TESTS. THE OHMMETER CAN DAMAGE THE THERMISTOR ELEMENTS OF THE TEMPERATURE SENSORS BEYOND REPAIR.
 (1)  Do a test of the temperature sensor fan:
 (a)  
Move the L PACK switch to HIGH, on the P5-10 panel.

 (b)  
Move the AIR TEMP switch to PASS CABIN, on the P5-17 panel.

 (c)  
Monitor the temperature indicator, on the P5-17 panel, and make a record of the cabin temperature.

 (d)  
Hold a thin sheet of paper near the air inlet grille of the temperature sensor fan, to see if there is air movement through the grille.

 NOTE: This will show that the temperature sensor fan is in
____
 operation.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-61-00
 ALL  ú ú 01 Page 506 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (e) (f) (g) (h) (i) (j) (k) (l)  Use the specified air velocity instrument to measure the air flow into the air inlet grille.Make sure the air velocity measurement is more than 150 feet per minute.Move the L PACK switch to AUTO.Make sure that the temperature sensor fan continues to operate.Move the L PACK switch to OFF.Make sure that the temperature sensor fan stops.Move the AIR TEMP switch to SUPPLY DUCT.Monitor the temperature indicator and make sure the supply duct temperature is approximately the same as the cabin temperature.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 空調 AIR CONDITIONING 2(127)