20-10-07
 ALL  ú ú 02 Page 209 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 022-052
 (4)  
Carefully move the card out along the guides.

 S 022-053

 (5)  
Remove the card assembly.

 TASK 20-10-07-422-038
 6.  Card Assembly - Installation____________________________
 A. References
 (1)  
AMM 20-40-12/201, Electro-Static Sensitive Devices

 B.
Access

 (1)  
Location Zones
 100 Lower Half of Fuselage

 C.
Procedure

 S 422-081
 (1)  
Install the card assembly in the guides. Carefully push the card in until the card is tightly engaged in the electrical connector.

 S 212-054

 (2)  
Make sure the ejectors are level against the card.

 (3)  
Close the applicable circuit breakers.

 (4)  
Close the card file door.

 S 862-082
 S 412-056
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-10-07
 ALL  ú ú 02 Page 210 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 CONTROL CABLE QUICK STOPS - REMOVAL/INSTALLATION
________________________________________________
 1.  General_______
 A.  This procedure contains one task. The task is the replacement of the control cable quick stops (referred to as cable stops in this procedure).
 B.  Cable stops give protection to the control stand cable drums if an engine separation occurs.
 TASK 20-10-08-964-001
 2.  Replace the Cable Stop (Fig. 401)______________________
 A.  References
 (1)  AMM 20-10-44/401, Lockwires
 B.  Remove the Cable Stop
 S 034-002
 (1)  Remove the lockwire that connects the cable stop to the swaged cable terminal stud.
CABLE STOP LOCKWIRE  SWAGED CABLE

Control Cable Stops Installation
Figure 401

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-10-08
 ALL  ú ú 01 Page 401 ú Mar 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
C51747
A
737-300/400/500MAINTENANCE MANUAL
 S 024-003
 (2)  
Move the cable stop longitudinally away from the terminal stud until the cable stop disengages.

 S 024-004

 (3)  
Move the cable stop laterally and let the cable go through the slot in the cable stop.

 C.
Install the Cable Stop

 S 424-005
 (1)  
With the large center hole of the cable stop to the swaged cable terminal stud, move the slot of the cable stop over the cable.

 S 424-006

 (2)  
Push the cable stop on the end of the swaged cable terminal stud until the cable stop fully engages.

 S 824-007

 (3)
Twist the swaged cable terminal stud to get the dimension shown.

 S 434-008

 (4)  
Install the lockwire from the cable stop to the swaged cable terminal stud (AMM 20-10-44).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-10-08
 ALL  ú ú 01 Page 402 ú Mar 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 CONTROL CABLE PULLEYS - REMOVAL/INSTALLATION
____________________________________________
 1.  General
_______
 A.  This procedure contains two tasks. The first task is the removal of the control cable pulley. The second task is the installation of the control cable pulley.
 B.  This procedure is the general procedure for removal and installation of pulleys. Fig. 401 shows examples of pulleys.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 STANDARD PRACTICES(9)