(c)  
Use an ohmmeter to make sure the resistance is less than 10 megohms.

 (d)  
Connect the strap to an applicable electrostatic ground jack.

 S 022-027
 (3)  Remove the unit with the ESDS placard from the equipment rack, the airframe, or the panel as shown in the applicable Removal/Installation procedure.
 NOTE: Make sure you do not touch the pins in the electrical
____ connector. Make sure a static sensitive placard is installed adjacent to the electrical connector(s). This static sensitive placard, or an equivalent, will be shown:
 CAUTION ELECTROSTATIC SENSITIVE DEVICE. CONDUCTIVE CONNECTOR DUST COVER REQUIRED.
 This placard shows that the unit can be damaged by an electrostatic discharge through the connector pins.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-40-12
 ALL  ú ú 02 Page 207 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 S 032-028
 (4)  Install a conductive dust cover with a static sensitive placard on the connectors, and standard dust covers on the connectors that do not have the placard.
 NOTE: The conductive dust caps and the connector covers are black
____
 in color.

 NOTE: The conductive dust caps and the connector covers from the
____ installed unit can be used on the removed unit.
 S 862-029
 (5)  
Move the unit, as shown in the standard practices, with the conductive dust caps and connector covers installed.

 S 022-054

 (6)  
Remove the strap.

 TASK 20-40-12-402-030
 5. ESDS Metal Encased Unit Installation
____________________________________
 A. General
 (1)  This task provides instructions to install an ESDS metal encased unit.
 CAUTION: MAKE SURE YOU KEEP CONTAMINATION OR UNWANTED MATERIAL AWAY FROM
_______ THE SENSITIVE DEVICE. CONTAMINATION OR UNWANTED MATERIAL NEAR THE SENSITIVE DEVICE CAN CAUSE A MALFUNCTION IN THE SENSITIVE DEVICE.
 (2)  
Obey this CAUTION during all of this task.

 B.
Equipment

 (1)  
Ohmmeter - Resistance Measuring Bridge
 (commercially available)

 (2)  
Strap (or alternative tool)

 (a)  
2214 Strap - Adjustable Wrist, Conductive, "CHARGE GUARD" with 5' coiled cord (recommended)

 Minnesota Minning and Mfg. Co. (Vendor code 57707) 3M Austin Center, Austin TX 78769-2963

 (b)  
9070 Strap - Wrist, Grounded, Adjustable with 6' coil ground cord (alternative)

 Desco Industries Inc. (Vendor code 62576), 761 Penarth Ave., Walnut, CA 91789-3028
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-40-12
 ALL  ú ú 02 Page 208 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (3)  Conductive electrical dust caps and connector covers
 NOTE: Conductive dust caps and connector covers are black or grey
____
 in color.

 (4)  Anti-static dust caps and connector covers (alternate when
 conductive caps and covers not available)

 (a)  Plastic dust caps and connector covers that have an anti-static solution applied and are dated.
 C. Install the Metal Encased Units with ESDS Placards
 S 862-031
 (1) Remove the system electrical power with the applicable procedure.
 S 762-057
 WARNING: USE A WRIST STRAP WITH A MINIMUM GROUNDING LEAD RESISTANCE OF
_______ 250 KILOHMS AND A MAXIMUM OF 1.5 MEGOHMS. USE OF A LOW RESISTANCE WRIST STRAP CAN CAUSE INJURY TO PERSONS IF A HIGH VOLTAGE SOURCE IS TOUCHED.
 (2)  Do these steps to do a resistance test of the strap:
 (a)  Use an ohmmeter to make sure the strap assembly has minimum resistance of 250 kilohms and a maximum of 1.5 megohms.
 CAUTION: THE GROUNDING LEAD ON THE WRIST STRAP MUST TOUCH THE SKIN
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 STANDARD PRACTICES(149)