BACS13BX SWAGE GROOVE DEPTH LIMITS
NOTE: ALL DIMENSIONS ARE IN INCHES.
Groove Depth Measurement for BACS13BX Sleeves
Figure 816
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-51
ALL ú ú 02 Page 872 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
L10099
A 737-300/400/500MAINTENANCE MANUAL
150
TORQUE WRENCH DIAL - PROCEDURE TO READ TORQUE
MATERIAL SWAGE TORQUE (POUNDS-INCH)
WALL THICKNESS - INCHESTUBE
SIZE TITANIUM 3AL-2.5V 1 CRES 21Cr-6Ni-9Mn 2 MIN MAX
04 0.016 0.016 4 5
06 0.019 0.020 1 2 1 5
08 0.026 0.026 20 25
10 0.032 0.033 40 45
12 0.039 0.039 40 45
16 0.051 0.052 80 85
SWAGER TORQUES NECESSARY TO ROLLER SWAGE BACS13BX SLEEVES
TO Ti-3AL-2.5V CWSR OR 21-6-9 CRES TUBE USING HARRISON 6633K01
ROLLER SWAGING KIT
AS SPECIFIED IN SPECIFICATION AMS 4945/BMS 7-234 AS SPECIFIED IN SPECIFICATION BMS 7-185
Swage Torques, Sleeve Dimensions, and Wall Thicknesses for Roller Swaging
Figure 817 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-51
ALL ú ú 02 Page 873 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
L10207
A 737-300/400/500MAINTENANCE MANUAL
BACS13BX SLEEVE
DIA G
TUBE
Swage Torques, Sleeve Dimensions, and Wall Thicknesses for Roller Swaging
Figure 817 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-51
ALL ú ú 02 Page 874 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
L10288
A 737-300/400/500MAINTENANCE MANUAL
SWAGED JOINT WALL THICKNESS (SEE TABLE)
SECTION OF ROLLER SWAGED JOINT
TUBE DIMENSIONS TUBE "NOMINAL" WALL SWAGED JOINT WALL THICKNESS FOR SIZE THICKNESS - INCHES "NOMINAL" TUBE WALLS - INCHES
3
TOLERANCE +0.002 -0.003
SWAGED JOINT WALL THICKNESS SPECIFICATION
"NOMINAL" WALL THICKNESS DEFINITION: TUBE WALL THICKNESS WITHOUT TOLERANCES AS SPECIFIED BY TUBE SPECIFICATION: AMS 4945 FOR Ti-3AL-2.5V AND BMS 7-185 FOR 21-6-9 CRES.
IF THE THICKNESS OF A MEASURED TUBE WALL IS DIFFERENT THAN THE "NOMINAL", ADD OR SUBTRACT THE DIFFERENCE FROM THE NECESSARY SWAGED JOINT WALL THICKNESS FOR "NOMINAL" TUBE WALLS.
EXAMPLE: 1. MEASURED 10 SIZE TITANIUM 3AL-2.5V TUBE WALL = 0.035 INCH
2.
WALL DIFFERENCE IS 0.035 INCH, MINUS 0.032 INCH = 0.003 INCH
3.
ADD 0.003 INCH TO 0.101 INCH = 0.104 INCH
Swage Torques, Sleeve Dimensions, and Wall Thicknesses for Roller Swaging
Figure 817 (Sheet 3)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-51
ALL ú ú 02 Page 875 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
L10299
A
737-300/400/500MAINTENANCE MANUAL
ST878D TOOL ASSEMBLY
ST878D TOOL ASSEMBLY
Preset Pressures (PSI) for the Cherry G-85 Lockbolt Gun with ST878D Presetting Tool Assembly (BACS13AP Sleeves) Figure 818 (Sheet 1)
L10312
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-51
ALL ú ú 02 Page 876 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 STANDARD PRACTICES(66)
