(2)
You must examine the conditions and be careful. Customer airlines must know how heat guns, soldering guns, and soldering irons are used.
(3)
Heat guns, soldering guns, and soldering irons can cause an explosion. Components in all of these devices can operate at temperatures higher than the fuel ignition temperature (450°F). Heat guns and soldering guns also can contain electrical switches which can cause sparks. These sparks can cause the fuel to burn.
(4)
We do not recommend you use a device to supply heat in the fuel tanks. You can have a good flow of air in the fuel tanks. You can make them safe when you fill the fuel tanks with nitrogen. For the repair of the wires in the fuel tanks, we recommend you use procedures that use crimped splices and sleeves with nylon ties. These procedures are specified in WDM Chapter 20.
(5)
Do not use heat guns, soldering guns, or soldering irons less than 100 feet from an airplane during these operations:
-
When you fuel
-
When you defuel
-
When the fuel tanks are open.
(6)
You can use heat guns, soldering guns, and soldering irons when and where smoking is permitted. If you use these devices where smoking is not permitted, you must first make sure there are not dangerous levels of fuel fumes in the work area.
(7)
Zero is the safe fuel fume level at which to use devices that can cause ignition.
(8)
Measure the fuel fume level with a combustible gas indicator that reads in "PERCENT LOWER EXPLOSIVE LIMIT" or "PERCENT EXPLOSIVE". For example, you can use Mine Safety Appliances, Model 2A or Davis, Model D-16. If you can read a fuel fume level on this equipment, two conditions occurred:
-A liquid fuel or fume source is near
-The local fuel fume levels are high or the ventilation is not
sufficient. Use the equipment to measure the initial fuel fume levels. Make sure the fuel fume levels are sufficiently low. Continue to monitor the fuel fume levels during the repair.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-27
ALL ú ú 01 Page 201 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(9)
Do not use a possible ignition source near open fuel tanks, fuel vents, or fuel leaks where fume concentrations cannot be known or controlled.
(10)
If you use a possible ignition source near an airplane where smoking is not permitted, make sure a person monitors the work and any other work in the area. The person must be authorized to monitor airplane fire safety.
(11)
A person who can measure the risk of the repair to be done must identify the emergency or fire fighting equipment necessary at the work area of the repair. The person must be authorized to monitor airplane fire safety.
(12)
Do not start or continue to do work on a fuel system component while equipment that can cause the fuel to burn is near.
(13)
Keep the number of maintenance and safety persons included to a minimum.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-27
ALL ú ú 01 Page 202 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
TEFLON BACKUP RINGS - REMOVAL/INSTALLATION
__________________________________________
1. General_______
A. This procedure contains one task. The task is the installation of teflon backup rings.
TASK 20-10-31-404-001
2. Teflon Backup Rings - Installation__________________________________
A. Procedure
S 424-002
(1) Install the teflon backup rings with the direction of the spiral clockwise and the scarfed edges as shown (Fig. 401).
TEFLON BACKUP RING SCARFED EDGE (2 LOCATIONS) SEE
(SHOWN LARGER THAN USUAL)
A
Teflon Backup Ring Installation Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 STANDARD PRACTICES(23)
