(2)  
Install hinge linkage cover (Detail B).

(a)  
Press cover over hinge mounting bracket until Nylatch fasteners are fully inserted. Do not press on plunger of fastener until body is fully inserted in bracket.

(b)  
Press in plungers of Nylatch fasteners to expand body and lock fastener in place (Section B-B).

B.  Install bullnose cover on filler panel and adjacent compartment.
(1)
Insert slot near outboard edge of cover over lower flange of PSU support beam.

(2)
Press slot on inboard edge of cover over attach bulb below compartment door.

C.  Install Passenger Service Unit on adjacent compartment (Ref 25-23-511).
507 
Feb 15/79  BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  25-24-512 Page 405 

CABIN ATTENDANTS' STATIONS - DESCRIPTION AND OPERATION
1.  General
A.  An attendant's station is provided near the forward entry and the aft service doors. Each forward and aft station accommodates two persons, and includes a double seat, a service unit, a boarding light and an attendants' panel. The seats are made up of component parts that may be installed or removed independently. Each seat is spring-loaded to move to the folded position when not in use. The seat bottom cushions are readily removable for use as flotation devices. A recess is provided in the seat back cushion for stowing two life vests. Adjacent to the seat at each station is a service unit containing two oxygen masks. For additional information on the service units, refer to 25-23-0.
2.  Attendant's Forward Station
A.  The attendant's forward station includes the attendant's seat, a boarding light, a service unit and an attendants' panel. The cabin attendants' panel is recessed in the ceiling above the forward galley door. The service unit is recessed in the ceiling above the attendants’ seat. The boarding light is recessed into the ceiling over the entry door. The attendant's seat is made up of parts: a backrest, a seat bottom, and a headrest, if installed. Each of these components is independently attached to the aft partition of the forward lavatory.
3.  Attendant's Aft Station
A.  The attendant's aft station includes the attendant's seat, a boarding light, a service unit and an attendants' panel. The cabin attendants' panel is recessed into the partition adjacent to the attendant's seat. The service unit is recessed in the ceiling above the attendant's seat. The boarding light is recessed into the ceiling above the entry door. The attendant's seat is made of independently attached parts: a backrest, a seat bottom, and a headrest, if installed.
4.  Attendants’ Galley Stations
A.  The galley station consists of a cabin attendants’ panel recessed in the ceiling above the galley door.
540 
May 20/82  BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  25-25-0 Page 1 

CABIN ATTENDANTS' SEATS - MAINTENANCE PRACTICES
1.  General
A.  The seat bottom has two cushions. These cushions are attached to the seat assembly with velcro tape and are designed to provide flotation for the flight attendants if required. A pull, separating the velcro tape, will free the cushions for emergency use. Two straps of nylon webbing are attached to the underside of the cushions to provide handholds.
B.  When provided, a recess in the seat back cushion may be used for stowing two life vests.
2.  Removal/Installation Attendants Seats (Fig. 201)
A.  Remove Attendants' Seat
(1)  
Remove Seat Backrest and Headrest (if installed).

(a)  Grasp seat backrest and headrest, if installed, firmly and pull loose from velcro tape holding it in place.

(2)  
Remove Seat

(a)  
Remove slide track stops.

(b)  
Remove fasteners and spacers attaching link arms to slide track.

(c)  
Slide seat up and out of slide tracks.

B.  Install Attendants' Seat
(1)  
Install Seat

(a)  
Hold seat in mounting position and insert into slide tracks.

(b)  
Attach link arms to slide track using screws or bolts and spacers.

(c)  
Install nut and cotter pin if required.

(d)  
Install slide track stops.

(2)  
Install Seat Backrest and Headrest (if installed).

(a)  
Hold seat back and headrest, if installed, in mounting position.

(b)  
Engage velcro tape on seat back and headrest with matching velcro tape on partition by placing seat backrest and headrest in position and pressing it firmly against partition.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 AMM 飛機維護手冊 EQUIPMENT/FURNISHINGS(100)