C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 73-21-40-000-001 Removal of the T12 Temperature Sensor AMM 73-21-40-400-001 Installation of the T12 Temperature Sensor AMM 73-21-50-000-043 Removal of the HJ10 Harness AMM 73-21-50-210-002 Visual Inspection of the Wiring Harnesses AMM 73-21-50-400-043 Installation of the HJ10 Harness AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU) AMM 73-21-60-400-001 Installation of the Electronic Control Unit (ECU) AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with
 Engine non Motoring)
 ASM 73-25/18

 3. Fault Confirmation
__________________
 A. Do the operational test of the FADEC 1B on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
 F 『 EEFF : ALL E ∞∞73-20-00∞∞∞∞∞∞∞∞∞∞Page 275
 E E Aug 01/05 ERE ECES

 F 『
 E C F M E
 E E
 E 56 E
 E E

 4. Fault Isolation
_______________
 A. The failure message is generated if channel B input from the T12 temperature sensor is invalid or out of range.
 (1) If the failure messsage T12 SNSR, J10, ECU is not confirmed:
 - replace the T12 temperature sensor (Ref. AMM TASK 73-21-40-000-001) and (Ref. AMM TASK 73-21-40-400-001).
 NOTE : Such a failure can be intermittent and therefore requires the
____ replacement of the T12 temperature sensor as a first maintenance action.
 (2) If the failure message T12 SNSR, J10, ECU is not confirmed but is repetitive:
 - do the following procedure after the replacement of the T12 temperature sensor.
 (a) Disconnect the harness HJ10 from the T12 temperature sensor (C102 connector) (Ref. ASM 73-25/18):
 - visually examine the receptacle and the connector for damaged pins and contamination (Ref. AMM TASK 73-21-50-210-002).
 1 If damage is found:
_ - repair or replace as required.
 2 If no damage is found:
_
 - do a cleaning of the connectors using a bristle brush and stoddard solvent (Material No. CP2011) (Ref. AMM TASK 73-21-50-210-002).
 3 If the fault continues during the subsequent flights:
_
 - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
 4 If the fault continues during the subsequent flights:
_
 - replace the harness HJ10 (Ref. AMM TASK 73-21-50-000-043) and (Ref. AMM TASK 73-21-50-400-043).
 (3) If the failure message T12 SNSR, J10, ECU is confirmed:
 - replace the T12 temperature sensor (Ref. AMM TASK 73-21-40-000-001) and (Ref. AMM TASK 73-21-40-400-001).
 (a) Disconnect the harness HJ10 from the T12 temperature sensor (C102 connector) (Ref. ASM 73-25/18):
 - visually examine the receptacle and the connector for damaged pins and contamination (Ref. AMM TASK 73-21-50-210-002).
 1 If damage is found:
_ - repair or replace as required.
 F 『 EEFF : ALL E ∞∞73-20-00∞∞∞∞∞∞∞∞∞∞Page 276
 E E Aug 01/05 ERE ECES

 F 『
 E C F M E
 E E
 E 56 E
 E E
 2 If no damage is found:

_
R  - clean the connector and receptacle with a bristle brush and
R  stoddard solvent (Material No. CP2011) (Ref. AMM TASK 73-21-50-210-002).
 - do the electrical resistance test through the T12 temperature sensor between: . pins 1 and 2 (160 to 250 ohms) . pin 1 and the ground (>10 megohms).
 3 If the resistance values are out of the specified limits:
_
 - replace the T12 temperature sensor (Ref. AMM TASK 73-21-40-000-001) and (Ref. AMM TASK 73-21-40-400-001).
 4 If the resistance values are in the specified limits:
_
 - connect the harness HJ10 to the T12 temperature sensor (C102 connector),

 - disconnect the harness HJ10 from the ECU (4000KS) (Ref. ASM 73-25/18),

 - visually examine the receptacle and the connector for damaged pins and contamination (Ref. AMM TASK 73-21-50-210-002).

 a If damage is found:
_
 - repair or replace as required.
 b If no damage is found:
_
R  - clean the connector and receptacle with a bristle brush
R  and stoddard solvent (Material No. CP2011) (Ref. AMM TASK 73-21-50-210-002).
 - do the electrical resistance test through the harness HJ10 between: . pins 18 and 19 (160 to 250 ohms) . pins 18 and 7 (>10 megohms) . pin 18 and the ground (>10 megohms).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發動機燃油和控制 1(95)