R 4. Fault Isolation
_______________
R A. If the test gives the maintenance message BSV(OP), J14(WRONG):
R - Verify the nameplate of the engine:
R (1) If the nameplate is for a SAC engine:
R - verify that a SAC ID plug is installed
R NOTE : The ID plug can be checked on the MCDU screen. Access
____ R reporting functions, then select the LRU Idenfication screen.
R Line 4 of the LRU Identification screen will display: R - "EGT MON" or "SAC CONFIG" for a SAC ID plug R - "DAC CONFIG" for a DAC ID plug
R (a) Replace the J14 Identification Connector (Ref. AMM TASK 73-21-90-R 000-002) (Ref. AMM TASK 73-21-90-400-002) or Do a Re-programming R of the Identification Connector (Push-pull Design only) (Ref. AMM R TASK 73-21-90-860-001).
R (2) If the nameplate is for a DAC engine:
R (a) Do a borescope inspection of the combustion chamber (Ref. AMM R TASK 72-41-00-290-001) and the high pressure turbine nozzle R assembly (Ref. AMM TASK 72-51-00-290-004).
R (b) Disconnect the cables HJ7 and HJ8 from the ECU and do a check of R the cable resistance between:
R . pins 6 and 7 (26 to 36 ohms)
R 1_ If the resistance value are specified limits:
R - Replace the BSV (Ref. AMM TASK 73-11-70-000-001) and (Ref.
R AMM TASK 73-11-70-400-001)
R 2_ If the resistance value are out of specified limits:
R - Disconnect the cables HJ7 and HJ8 from the HMU and do a
R check of the HMU resistance between:
R . pins 6 and 7 (26 to 36 ohms)
R a_ If the resistance value are in specified limits:
R - replace harness HJ7 (Ref. AMM TASK 73-21-50-000-040)
R (Ref. AMM TASK 73-21-50-400-040) and/or harness HJ8 (Ref.
R AMM TASK 73-21-50-000-041) (Ref. AMM TASK 73-21-50-400-R 041)
R b_ If the resistance value are out of specified limits:
R - Replace HMU (Ref. AMM TASK 73-21-10-000-001) (Ref. AMM
R TASK 73-21-10-400-001)
R (3) if the fault continues, replace the ECU (4000KS) (Ref. AMM TASK 73-R 21-60-000-001) (Ref. AMM TASK 73-21-60-400-001).
F 『
∞∞73-10-00∞∞∞∞∞∞∞∞∞∞Page 257
EEFF : ALL E
E E May 01/03
E E
ECES E
F 『
E C F M E
E E
E 56 E
E E
R B. Do the test given in Para. 3.A.
F 『 EEFF : ALL E ∞∞73-10-00∞∞∞∞∞∞∞∞∞∞Page 258
E E May 01/03 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
R TASK 73-10-00-810-847
R Failure of the BSV Closed on Engine 1
R 1. Possible Causes_______________
R - J14 Identification Connector R - BSV R - harness HJ7 R - harness HJ8 R - HMU R - ECU (4000KS)
R 2. Job Set-up Information______________________
R A. Referenced Information
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION R -------------------------------------------------------------------------------
R AMM 72-41-00-290-001
R
R
R
R AMM 72-51-00-290-004
R
R AMM 73-11-70-000-001
R AMM 73-11-70-400-001
R AMM 73-21-10-000-001
R AMM 73-21-10-400-001
R AMM 73-21-50-000-040
R AMM 73-21-50-000-041
R AMM 73-21-50-400-040
R AMM 73-21-50-400-041
R AMM 73-21-60-000-001
R AMM 73-21-60-400-001
R
R AMM 73-21-90-000-002
R AMM 73-21-90-400-002
R AMM 73-21-90-860-001
R
R AMM 73-29-00-710-040
R
R 3. Fault Confirmation__________________
R A. Test
Borescope Inspection of the Combustion Chamber Liners, Dome Areas,High Pressure Turbine Nozzle Vanes and Shrouds (as far as visible through two opposite ports) Borescope Inspection of High-Pressure Turbine Nozzle Assembly Removal of the Burner Staging Valve (BSV) Installation of the Burner Staging Valve (BSV) Removal of the Hydromechanical Unit (HMU) Installation of the Hydromechanical Unit (HMU) Removal of the HJ7 Harness Removal of the HJ8 Harness Installation of the HJ7 Harness Installation of the HJ8 Harness Removal of the Electronic Control Unit (ECU)(4000KS) Installation of the Electronic Control Unit (ECU)(4000KS) Removal of the Engine Identification Connector Installation of the Engine Identification Connector Programming of the Identification Connector (Push-Pull Design) Operational Test of the FADEC on the Ground (with Engine Motoring) 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發動機燃油和控制 1(58)
