F 『
E C F M E
E E
E 56 E
E E
2 If the resistance values are out of the specified limits:
_ R - disconnect the harness CJ11R at the T25 temperature sensor. R - do a visual inspection of the harness connector and R receptacle. Look for contamination or oxidation or pins that R have damage. R - if you find damage, repair or replace as required. R - clean the connector and receptacle with a bristle brush and R stoddard solvent (Material No. CP2011) (Ref. AMM TASK 73-21-R 50-210-002). R - do a check of the T25 sensor resistance between: R
. pins 1 and 2 (160 to 250 Ohms) . pin 1 and the ground (> 10 Megohms).
a If the resistance values are in the specified limits:
_
- replace the harness CJ11R (Ref. AMM TASK 73-21-50-000-026) and (Ref. AMM TASK 73-21-50-400-026).
b If the resistance values are out of the specified limits:
_
- replace the T25 temperature sensor (Ref. AMM TASK 73-21-20-000-002) and (Ref. AMM TASK 73-21-20-400-002).
B. Do the test given in Para. 3.A.
F 『 EEFF : ALL E ∞∞73-20-00∞∞∞∞∞∞∞∞∞∞Page 247
E E Aug 01/05 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
TASK 73-20-00-810-854
Loss of the T25 Sensor Signal through the Channel A on Engine 2
1. Possible Causes
_______________
- harness J11
- ECU (4000KS)
- harness CJ11R
- T25 temperature sensor
2. Job Set-up Information
______________________
R A. Fixtures, Tools, Test and Support Equipment
R -------------------------------------------------------------------------------R REFERENCE QTY DESIGNATION
R -------------------------------------------------------------------------------
R No specific bristle brush
R B. Consumable Materials
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R Material No. CP2011 *
R stoddard solvent (Ref. 70-30-00)
R C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
R AMM AMM AMM AMM AMM AMM AMM AMM AMM 73-21-20-000-002 73-21-20-400-002 73-21-50-000-026 73-21-50-000-044 73-21-50-210-002 73-21-50-400-026 73-21-50-400-044 73-21-60-000-001 73-21-60-400-001
AMM 73-29-00-710-040
ASM 73-25/18
F EEFF : ALL E E ECES Removal of the T25 Temperature SensorInstallation of the T25 Temperature SensorRemoval of the CJ11R HarnessRemoval of the HJ11 Harness Visual Inspection of the Wiring HarnessesInstallation of the CJ11R HarnessInstallation of the HJ11 HarnessRemoval of the Electronic Control Unit (ECU)(4000KS)Installation of the Electronic Control Unit (ECU)(4000KS)Operational Test of the FADEC on the Ground (with Engine non Motoring)
『E
∞∞73-20-00∞∞∞∞∞∞∞∞∞∞Page 248
E Aug 01/05EE
F 『
E C F M E
E E
E 56 E
E E
3. Fault Confirmation
__________________
A. Do the operational test of the FADEC 2A on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
4. Fault Isolation
_______________
A. If the test gives the maintenance message T25 SNSR, J11, ECU:
- do a check for open or short to ground of the harness J11 between the ECU (4000KS) and the 6 o'clock junction box, between the 6 o'clock junction box and the T25 temperature sensor pins J11/19, 37, 38 to pins J11/1, 2, 3 (Ref. ASM 73-25/18).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發動機燃油和控制 1(83)
