C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
28-00-00-910-001 Fuel Safety Procedures 28-10-00-910-001 Safety Procedures When You Do Work in a Fuel Tank 28-10-00-910-002 Access to the Fuel Tanks and the Work Areas 57-27-11-000-001 Removal of the Access Panel (540AB, 540BB, 540CB,
540DB, 540EB, 540FB, 540GB, 640AB, 640BB, 640CB, 640DB, 640EB, 640FB, 640GB)
57-27-11-400-001 Installation of the Access Panel (540AB, 540BB, 540CB, 540DB, 540EB, 540FB, 540GB, 640AB, 640BB, 640CB, 640DB, 640EB, 640FB, 640GB)
ASRM 572100 (for corrective action) R 57-20-00-991-008 Fig. 609
3. Job Set-up
__________
Subtask 57-20-00-941-056
A. Safety Precautions
WARNING : OBEY THE FUEL SAFETY PROCEDURES.
_______
(1)
Obey the fuel safety precautions (Ref. TASK 28-00-00-910-001) and (Ref. TASK 28-10-00-910-001).
(2)
Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.
(3)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(4)
Put the safety barriers in position.
Subtask 57-20-00-010-056
B. Get Access
WARNING : OBEY THE SAFETY PROCEDURES WHEN YOU DO WORK IN A FUEL TANK.
_______
(1)
Put the access platform in position below the zone 540(640).
(2)
Remove the applicable access panels:
-
for the left wing, remove 540AB
-
for the right wing, remove 640AB (Ref. TASK 57-27-11-000-001) and (Ref. TASK 28-10-00-910-002).
(3)
Open the RIB2 surge doors:
-
for the left wing, open 540BZ
-
for the right wing, open 640BZ.
(4)
Install the HOOK-COVER (RIB 2 SURGE DOORS) (98D57004013000) on the forward surge doors.
(5)
Install the HOOK-COVER (RIB2-SURGE DOORS) (98D57004014000) on the aft surge doors.
4. Procedure
_________
R (Ref. Fig. 609/TASK 57-20-00-991-008)
Subtask 57-20-00-110-057
A. Preparation for Inspection
(1) Use a clean MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026), to clean:
-the rear-spar forward-face upper and lower root-joint fittings.
Subtask 57-20-00-210-055
B. Detailed Visual Inspection of the Outer Wing Rear-Spar Forward-Face Upper and Lower Root-Joint Fittings
(1) Examine the rear-spar forward-face upper and lower root-joint fittings. Make sure that:
-
there is no corrosion or damage
-
there are no scratches or scores
-
there are no loose or damaged fasteners
-the surface protection is in the correct condition.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 572100) for the
____
correct repair procedure.
Details of the Rear-Spar Forward-Face (Upper and Lower Root-Joint Fitting) R Figure 609/TASK 57-20-00-991-008
1EFF : ALL 1 57-20-00Page 648 1 1 Aug 01/05 1 1 1CES 1
5. Close-up
________ Subtask 57-20-00-410-057
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the HOOK-COVER (RIB 2 SURGE DOORS) from the forward surge doors.
(3)
Remove the HOOK-COVER (RIB2-SURGE DOORS) from the aft surge doors.
(4)
Close the RIB2 surge doors:
-
for the left wing, close 540BZ
-
for the right wing, close 640BZ.
(5)
Install the applicable access panels:
-for the left wing, install 540AB
-for the right wing, install 640AB (Ref. TASK 57-27-11-400-001). Subtask 57-20-00-942-057
B. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER from the flap/slat control lever.
(3)
Remove the warning notice(s).
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼1(80)
