____
correct repair procedure.
5. Close-up
________ Subtask 57-20-00-942-091
A. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
(3)
Remove the warning notice(s).
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 57-20-00Page A672 1 1 Aug 01/05R 1 1 1CES 1
TASK 57-20-00-210-005
General Visual Inspection of Outer Wing, Bottom Skin, Lower Surface at Attachment to Ribs and Stringers, in Area covered by Pylon Fairing
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 572042-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific adjustable access platform No specific safety barriers No specific warning notices 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1 SOLVENT GENERAL PURPOSE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
1EFF : ALL 1 57-20-00Page A673 1 1 Aug 01/05R 1 1 1CES 1
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 064154 P.Block 1 ASRM 572000 (for corrective action) R 57-20-00-991-041 Fig. 633
3. Job Set-up
__________
Subtask 57-20-00-941-091
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.
(3)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
Subtask 57-20-00-010-088
B. Get Access
(1)
Put the adjustable access platform in position at the applicable engine pylon zone 471(481).
(2)
Remove the applicable access panels (Ref. AMM 064154 P.Block 1):
-
for the left wing: 471AL, 471BL, 471CL, 472AR, 472BR, 475BL, 475CL, 476BR, 476CR
-
for the right wing: 481AL, 481BL, 482AR, 482BR, 482CR, 485BL, 485CL, 486BR, 486CR.
4. Procedure
_________
R (Ref. Fig. 633/TASK 57-20-00-991-041)
Subtask 57-20-00-100-052
A. Preparation for Inspection
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the applicable area for inspection.
Subtask 57-20-00-210-078
B. General Visual Inspection of Outer Wing, Bottom Skin, Lower Surface at
Attachment to Ribs and Stringers, in Area covered by Pylon Fairing
(1) Do an inspection and make sure that:
-
there is no damage
-
there are no cracks
-
there is no corrosion
-the paint finish is in the correct condition.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 572000) for the
____
correct repair procedure.
5. Close-up
________
Subtask 57-20-00-410-090
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the applicable access panels (Ref. AMM 064154 P.Block 1):
-
for the left wing: 471AL, 471BL, 471CL, 472AR, 472BR, 475BL, 475CL, 476BR, 476CR
-
for the right wing: 481AL, 481BL, 482AR, 482BR, 482CR, 485BL, 485CL, 486BR, 486CR.
中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼1(111)
