B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
 Configuration before Maintenance Action 49-00-00-480-001 Installation of the APU Hoist Tool (APS 3200) 52-41-00-010-001 Open the APU Doors for Access 52-41-21-000-001 Removal of the APU Access Door 315AL 52-41-22-000-001 Removal of the APU Access Door 316AR and the related
 Door Mechanism 49-12-51-991-002 Fig. 401
 3. Job Set-up
__________
 Subtask 49-12-51-860-051
 A. Aircraft Maintenance Configuration
 (1)
 Put the warning notices on panel 25VU to tell persons not to start the APU.

 (2)
 Energize the ground service network (Ref. TASK 24-41-00-861-002).

 (3)
 Make sure that the hydraulic systems are depressurized (Ref. TASK 29-00-00-864-001).

 Subtask 49-12-51-865-053
 B. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41

 Subtask 49-12-51-010-051
 C. Get Access
 (1)
 Put the access platform below the access doors 315AL and 316AR.

 (2)
 Open the APU access doors 315AL, 316AR. (Ref. TASK 52-41-00-010-001)

 (3)
 Set the light switch 11LJ to on.

 (4)
 Remove the APU access doors 315AL, 316AR (Ref. TASK 52-41-21-000-001) (Ref. TASK 52-41-22-000-001).

 4. Procedure
_________ (Ref. Fig. 401/TASK 49-12-51-991-002) Subtask 49-12-51-480-051
 A. Installation of the HOIST- MINILIFT
 WARNING : OBEY THE HOISTING SAFETY PROCEDURES.

_______ MAKE SURE THAT THE HOIST IS ASSEMBLED AND ATTACHED CORRECTLY BEFORE YOU PUT A LOAD ON IT. OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE HOIST. IF THE HOIST IS IN AN INCORRECT CONDITION THE LOAD CAN MOVE ACCIDENTALLY AND KILL PERSONS OR CAUSE INJURY.
 CAUTION : DO NOT TURN THE HOIST HANDLE MORE THAN 90 DEGREES WHEN THE APU
_______ MOUNT BRACKETS ARE TIGHTLY ENGAGED ON THE VIBRATION ISOLATORS. IF YOU TURN THE HOIST HANDLE MORE THAN 90 DEGREES, YOU CAN CAUSE DAMAGE TO THE APU AND THE APU MOUNTS.
 (1)
 Install the HOIST - MINILIFT (Ref. TASK 49-00-00-480-001) Subtask 49-12-51-020-051

 B.
 Removal of the Vibration Isolator

 (1)
 Slowly wind the handle on the APU hoist until the APU hoist-cable is in tension.

 (2)
 Remove the nut (13) and install the PROTECTOR - THREADS, APU MOUNTING BOLTS on the cone bolt.

 (3)
 Remove and discard the cotter pins (1) and (7).

 (4)
 Remove the castle nuts (2) and (6), the washers (3) and (8) and the bolts (4) and (9).

 (5)
 Remove the tie-rods (5), (10) and (11) from the vibration isolator 4035KM (12).

 (6)
 Remove the vibration isolator (12) from the APU mount-bracket (14).

 (7)
 If necessary remove the tie-rods (5), (10) and (11).

 (a)
 Remove the nuts (19) and (23), the washers (21) and (25) the screws (22) and (26).

 (b)
 Remove the clamps (27) and (28).

 (c)
 Disconnect the bonding straps (20).

 (d)
 Remove and discard the cotter pins (18).

 (e)
 Remove the castle nuts (17), the washers (16) and the bolts (15).

 (f)
 Remove the tie-rod from the bracket.

 FWD LH Tie-Rods and Vibration Isolator
 Figure 401/TASK 49-12-51-991-002

 CES  5. Close-up

________  TASK 49-12-51-400-002

 Installation of the FWD LH Tie-Rods and Vibration Isolator 4035KM (APS 3200)
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER2(87)