(2)
 Remove the weight of the APU from the APU mount brackets CAUTION : DO NOT TURN THE HOIST HANDLE MORE THAN 90 DEGREES, AFTER

_______ YOU REMOVE THE SLACK FROM THE HOIST CABLE. IF YOU TURN THE HOIST HANDLE MORE THAN 90 DEGREES, YOU CAN CAUSE DAMAGE TO THE APU AND THE APU MOUNTS.
 (a) Operate the HOIST - MINILIFT until the weight of the APU is removed from the mounts.
 NOTE : Before you install the hoist handle, turn the upper drum
____ shaft of the HOIST - MINILIFT with your hand until you have removed the slack from the hoist cable. Then install the hoist handle on the upper drum shaft and turn the handle 90 degrees in clockwise direction. Thus you make sure that the weight of the APU is removed from the APU mounts.
 NOTE : Do a check and make sure that the HOIST - MINILIFT is
____ assembled and installed correctly and holds the load.
 (3)
 Put the SUPPORT FRAME - APU in position below the APU. Subtask 49-11-11-020-054-A

 C.
 Remove the APU from the APU Compartment

 (1) Removal of the mount nuts
 WARNING : OBEY THE HOISTING SAFETY PROCEDURES.

_______ MAKE SURE THAT THE HOIST IS ASSEMBLED AND ATTACHED CORRECTLY BEFORE YOU PUT A LOAD ON IT. OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE HOIST. IF THE HOIST IS IN AN INCORRECT CONDITION THE LOAD CAN MOVE ACCIDENTALLY AND KILL PERSONS OR CAUSE INJURY.

 (a)
 Remove the APU mount nuts (40), (47) and (48).

 (b)
 Install the PROTECTOR - THREADS, APU MOUNTING BOLTS to the threads (41) of the rear APU mount and the vibration isolators.

 (2) Removal of the APU from the APU mount vibration-isolators CAUTION : MAKE SURE THAT THE THREE ATTACHMENT NUTS ARE REMOVED AND
_______ THAT THE APU CAN MOVE DOWN FREELY. IF YOU DO NOT DO THIS, YOU CAN CAUSE DAMAGE TO THE TIE RODS WHEN YOU LOWER THE APU.
 CAUTION : MAKE SURE THAT ALL PLUMBING IS FREE FROM OBSTRUCTION.
_______
 (a) Remove the APU from the APU mount vibration-isolators and lower it carefully from the APU compartment.
 (3) Attachment of the APU to the SUPPORT FRAME - APU. CAUTION : MAKE SURE THAT ALL PLUMBING IS FREE FROM OBSTRUCTION.
_______
 (a)
 Attach the APU to the APU SUPPORT FRAME - APU NOTE : Make sure that the pip-pins are fully engaged in the

____ brackets of the APU support frame and the APU. Make sure that the screw at the rear of the APU support frame is fully engaged in the attachment plate and the APU.

 (b)
 Disconnect the HOIST - MINILIFT from the APU (Ref. TASK 49-00-00-080-001).

 (c)
 Put blanking covers on the APU exhaust flange.

 (4)
 Disconnection of replacement Components

 (a)
 Remove the Generator (80) (Ref. TASK 24-23-51-000-001).

 (b)
 Remove the FWD and AFT APU mount brackets (46) and (42)
 (Ref. TASK 49-12-54-000-001).

 (c)
 Remove the APU LP Switch 5030QM (Ref. TASK 28-22-14-000-001). NOTE : Keep these parts into a container for replacement at the

 (5)
 If you will not install a new APU, you must install the components of

____
 new component .

 the kit for the FLIGHT WITHOUT APU.

 TASK 49-11-11-400-003
 Installation of the Power Plant (APU) (APS 3200)
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
 No specific fiber-bristled brush
 No specific tie-wrap
 No specific container 1.0 l (0.2641 USgal)
 No specific access platform 3.5 m (11 ft. 6 in.)
 No specific Torque Wrench : range 0.00 to 1.20 m.daN

 (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
 (2.00 to 26.00 lbf.ft) No specific Torque Wrench : range 1.00 to 10.00 m.daN
 (8.00
 to 75.00 lbf.ft) 98A49107504001 3 PROTECTOR - THREADS, APU MOUNTING BOLTS 98D49207527000 1 SUPPORT FRAME - APU

 B.
 Consumable Materials

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 03-002  GB DEF-STAN 91-101 LUBRICATING OIL TURBINE ENGINE SYNT BASE (Ref. 20-31-00)
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER2(58)