(c)
 Remove the nuts (72), (75), the washers (73) and (76) which are temporarily installed on the terminal studs.

 NOTE : Make sure that the terminal studs, nuts and washers are in
____ correct condition. Replace any item found in not correct condition.
 NOTE : If it is necessary, carefully pull the positive electrical
____ lead from C80 until you can attach the cable correctly.
 NOTE : The positive electrical leads (77 and 78) must be directly
____ in conter with the starter motor copper strip, before the installation of the washer (76) and the nut (75).
 (d) Install the positive starter cable (78), the monitoring cable (77), the washer (76) and the nut (75) to the positive terminal stud.
 NOTE : The positive starter cable is identified through the label
____
 reading 8KAPOS.

 (e) Install the negative starter cable (74), the washer (73) and the nut (72) to the negative terminal stud.
 NOTE : The negative starter cable is identified through the label
____
 reading 8KANEG.

 (f)
 TORQUE the nut (75) of the positive starter cable to between 0.85 and 0.90 m.daN (75.22 and 79.64 lbf.in).

 (g)
 TORQUE the nut (72) of the negative starter cable to between 0.56 and 0.62 m.daN (49.55 and 54.86 lbf.in).

 (6)
 Connection of the Electrical Harness (Ref. Fig. 402/TASK 49-11-11-991-004)

 (a)
 Remove and discard the tie-wraps which temorarily attach the electrical connectors (50) P1, (51) P2 and (55) P3 to the APU.

 (b)
 Remove the blanking caps from the connectors.

 (c)
 Make sure the connectors are clean and in a correct condition.

 (d)
 Remove the temporarily installed bolt (61) and nut (62) from the clamp (60) on the FWD RH tie rod.

 (e)
 Put the clamp (63) in position on the clamp (60), install and tighten the bolt (61) and the nut (62).

 (f)
 Remove the temporarily installed bolt (56) and the washer (57) from the bracket (59) at the RH side of the APU compartment.

 (g)
 Make sure that the nut clip on the bracket (59) is in the correct position.

 (h)
 Put the clamp (58) into position, install the washer (57) and the bolt (56), tighten the bolt (56).

 (i)
 Install the connector (50) P1 to the correct connetor on the forward firewall.

 (j)
 Remove the temporarily installed bolts (54) and spacers (52) from the brackets on the APU compartment front firewall.

 (k)
 Make sure that the nut clips on the brackets (on the front firewall) are in the correct position.

 (l)
 Put the two clamps (53) in position, install the spacers (52) and bolts (54), tighten the bolts (54).

 (m)
 Install the connectors (51) P2 and (55) P3 to the correct
 connetors on the forward firewall.

 (7)
 Connection of the APU Fuel Line to the APU Fuel Control Unit (Ref. Fig. 401/TASK 49-11-11-991-002)

 WARNING : OBEY THE FUEL SAFETY PROCEDURES.
_______
 (a)
 Put the container in position below the fuel and control unit .

 (b)
 Remove the main fuel inlet pipe from the stowage bracket attached to the front firewall of the APU compartment.

 (c)
 Remove the plastic blanking plugs from the disconnected line ends.

 (d)
 Connection of the main fuel inlet pipe CAUTION : YOU MUST USE TWO WRENCHES AND HOLD THE COMPONENT WHEN

_______ YOU REMOVE/INSTALL THE PIPE COUPLINGS AND/OR UNIONS. THIS PREVENTS DAMAGE TO THE COMPONENT.

 1_ Apply LUBRICANTS (Material No. 06-001A) to the connector
 internal threads and connect the main fuel inlet pipe (20) to
 the vent and drain valve (21).

 2 TORQUE the nut of the main fuel inlet pipe (20) to between
_
 4.85 and 5.31 m.daN (35.76 and 39.15 lbf.ft). 3 Safety the nut with corrosion-resistant steel lockwire 0.8 mm
_
 (0.32 in.) dia. 4 Mark the nut of the main fuel inlet pipe (20) with PAINTS FOR
_ DETAIL (INTERNAL AND EXTERN AL) (Material No. 07-020) to identify the torqued position.
 (8)
 Installation of the the oil cooler outlet-duct

 (a)
 Remove the blanking covers from the oil cooler outlet and oil cooler duct.

 (b)
 Install the oil cooler outlet-duct (Ref. TASK 49-52-41-400-001).

 (9)
 Conection of the Bleed-Air Duct Elbow (Ref. Fig. 401/TASK 49-11-11-991-002)

 (a)
 Remove the blanking covers from the openings of the bleed-air duct elbow (3), and the bleed air duct of the APU (1).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER2(36)