(3)
 Put a warning notice in the cockpit to tell persons not to start the APU.

 (4)
 Make sure that hydraulic systems are depressurized
 (Ref. TASK 29-00-00-864-001).

 Subtask 49-11-00-865-053
 B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41
 Subtask 49-11-00-010-054
 C. Get Access
 (1)
 Put the access platform in position below the APU compartment.

 (2)
 Make sure that the APU access doors are open 315AL, 316AR (Ref. TASK 52-41-00-010-001).

 (3)
 Set the LIGHT SW 11LJ to the ON position.

 4. Procedure
_________ (Ref. Fig. 803/TASK 49-11-00-991-003) Subtask 49-11-00-420-051
 A. Installation of the Generator Substitution Kit
 (1)
 Clean the component interface and/or the adjacent area.

 (2)
 Remove the nuts (4) from the generator mounting flange (1).

 (3)
 Apply a thin layer of OILS (Material No. 03-002) on the O-ring (2) and install with the COVER - ASSEMBLY, APU GEN on the mounting flange (1).

 (4)
 Put the generator cable support (6) (Ref. AIPC 49110405010) in position on the cover assembly (3).

 (5)
 Tighten the cover assembly (3) and the generator cable support (6) with the nuts (4).

 (6)
 TORQUE the nuts (4) to between 3.9 and 4.4 m.daN (28.76 and 32.44 lbf.ft).

 (7)
 Make sure that the drain plug (5) is fully tightened and safety with lockwire-corrosion resistant steel 0.8mm (0.0314 in.) dia.

 (8)
 Remove the nuts (8) from the generator cable support (6). NOTE : Refer to the marks on the generator cable support when you

____
 install the electrical cable connections.

 (9)
 Connect the electrical connector (7) and the electrical cable connections (9) to the generator cable support (6).

 APU Generator 8XS-Replacement
 Figure 803/TASK 49-11-00-991-003

 CES

 (10)
 Tighten the electrical cable connections (9) with the nuts (8). Subtask 49-11-00-865-054

 B.
 Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41
 Subtask 49-11-00-210-052
 C. Inspection Check
 CAUTION : USE ONLY APPROVED TYPES/BRANDS OF LUBRICANTS. DO NOT MIX

_______
 TYPES//BRANDS OF LUBRICANTS.

 (1) Do a visual check of the oil quantity on the APU oil level. Add oil if the oil level is on or less than the ADD mark on the sight glass (Ref. TASK 49-90-00-600-001).
 Subtask 49-11-00-710-051
 D. Test WARNING : MAKE SURE THAT YOU HAVE THE CORRECT FIRE FIGHTING EQUIPMENT
_______
 AVAILABLE.

 (1)
 Start and operate the APU (Ref. TASK 49-00-00-860-003).

 (2)
 Examine the joint between the mounting flange (1) and the cover assembly (3) for oil leakage.

 NOTE : No leakage of oil is permitted.
____
 (3) Stop the APU (Ref. TASK 49-00-00-860-004).
 5. Close-up
________ Subtask 49-11-00-410-054
 A. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Set the LIGHT SW 11LJ to the OFF position.

 (3)
 Close the APU access doors 315AL, 316AR (Ref. TASK 52-41-00-410-001).

 (4)
 Remove the access platform(s). Subtask 49-11-00-860-059

 B.
 Aircraft Maintenance Configuration

 (1)
 Put a warning notice in the cockpit to tell persons that the APU -Generator is not installed.

 (2)
 Make an entry in the aircraft technical logbook.

 (3)
 Pressurize the reservoirs of the hydraulic systems.
 (Ref. TASK 29-14-00-614-002).

 (4)
 De-energize the ground service network
 (Ref. TASK 24-42-00-862-001).

 TASK 49-11-00-000-002
 Removal of the Generator Substitution Kit (GTCP 36-300)
 1. Reason for the Job
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER2(3)