(1)
 The test is controlled by the STATUS/HISTORY switch on the GPWC. The results are depicted on an 8-character BITE display also located on the face of the GPWC. The STATUS test is initiated if you momentarily select PRESENT STATUS with the STATUS/HISTORY switch. The HISTORY test is initiated if you momentarily select FLIGHT HISTORY with the STATUS/HISTORY switch. The STATUS test will depict the status of the latest flight information. The HISTORY test will depict the information related to the last ten flights. Both tests commence with ALL SEGMENTS TEST and terminate with END TEST messages. The computer faults are indicated by the message GPWC FAILED or FLT HIST INVALID. All other fault messages indicate an incorrect input condition.

 (2)
 The desired information is read from memory and converted to alphanumeric data for presentation on the BITE display. Messages are presented by means of this vocabulary:

R 1EFF : 001-049, 051-060, 101-104, 1 34-48-00Page 41 1 1 Config-2 May 01/05 1 1 1CES 1

 Status/History Test Readouts
 Figure 014

R 1EFF : 001-049, 051-060, 101-104, 1 34-48-00Page 42 1 1 Config-2 May 01/05 1 1 1CES 1

 IN TEST  INVALID  LAMPTEST
 END TEST  INACTIVE  AUDIO
 GPWS OK  INHIBIT  SELECT
 GPWC  PREVIOUS  FLIGHT-0
 RADIO  TEN  FLIGHT-1
 ALTIMETR  FLIGHTS  FLIGHT-2
 BARORATE  OK  FLIGHT-3
 AIRSPEED  FAILED  FLIGHT-4
 ALTITUDE  AIR DATA  FLIGHT-5
 GLIDE  ILS DATA  FLIGHT-6
 SLOPE  IRS DATA  FLIGHT-7
 CANCEL  EXTERNAL  FLIGHT-8
 COURSE  FLT HIST  FLIGHT-9
 GEAR  INPUT  CORRECTD
 RUNWAY  PROCESSR  LOCALIZR
 HEADING  OUTPUT  LATITUDE
 FLAPS  ASSEMBLY  LONGITUD

 (3) Examples of the STATUS test vocabulary are:
 GPWS OF GEAR INVALID GPWC FAILED

R 1EFF : 001-049, 051-060, 101-104, 1 34-48-00Page 43 1 1 Config-2 May 01/05 1 1 1CES 1

 (4) Examples of the HISTORY test vocabulary are:

 RADIO  BARORATE  ILS DATA
 ALTIMETR  INVALID  INACTIVE
 INACTIVE  FLIGHT-2  FLIGHT-3
 FLIGHT-1  FLIGHT-4
 FLAPS  PREVIOUS
 INVALID  TEN
 FLIGHT-8  FLIGHTS
 - OK

 (5)
 No aural warnings are broadcast during either test.

 (6)
 If the history test message you read is too long, you can stop the test. To do this, you must set the STATUS/HISTORY switch to PRESENT STATUS until the BITE display is blank. The display will then show CANCEL followed by END TEST. This operation will have no adverse effect on the data held in the flight history memory.

 (7)
 The sequences of the flight history test and those of the present status test will not activate the cockpit voice outputs.

 E. CFDS Interface
 (1) BITE description The BITE facilitates maintenance on in-service aircraft. It detects and identifies faults related to the GPWS. The BITE of the GPWC is connected to the CFDIU. The BITE:
 -transmits permanently GPWS status and its identification message to the CFDIU
 -memorizes the faults which occurred during the last 63 flight segments
 -monitors data inputs from the various peripherals (FMGC, RA transceiver, ILS receiver, ADIRU, SFCC, LGCIU, ECAM control panel and CFDIU)
 -transmits to the CFDIU the result of the tests performed
 -can communicate with the CFDIU through the menus. The BITE can operate in two modes:
 -
the normal mode

 -
the menu mode.

 (a) Normal mode During the normal mode, the BITE monitors cyclically the status of the GPWS. It transmits its information to the CFDIU during the concerned flight.
R 1EFF : 001-049, 051-060, 101-104, 1 34-48-00Page 44 1 1 Config-2 May 01/05 1 1 1CES 1

 In case of fault detection, the BITE stores the information in
 the fault memories.
 These items of information are transmitted to the CFDIU every 100
 ms by an ARINC 429 message with label 356.

 (b) Menu mode The menu mode can only be activated on the ground. This mode enables communication between the CFDIU and the GPWC BITE by means of the MCDU. The GPWS menu mode is composed of:
 -LAST LEG REPORT
 -PREVIOUS LEGS REPORT
 -LRU IDENTIFICATION
 -GROUND SCANNING
 -TROUBLE SHOOTING DATA
 -CLASS 3 FAULTS
 -TEST
 -GROUND REPORT.
 (Ref. Fig. 015, 016, 017)
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NAVIGATION 導航4(63)