(5)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : ALL 1 34-52-00Page 504 1 1 Feb 01/04 1 1 1CES 1
TASK 34-52-00-710-003 Operational Test of the ATC WARNING : MAKE SURE THAT ALL THE CIRCUITS IN MAINTENANCE ARE ISOLATED BEFORE
_______ YOU SUPPLY ELECTRICAL POWER TO THE AIRCRAFT.
1. Reason for the Job__________________ Self Explanatory
2. Job Set-up Information______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power
24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied
from the External Power 34-10-00-860-002 ADIRS Start Procedure 34-10-00-860-005 ADIRS Stop Procedure
3. Job Set-up
__________ Subtask 34-52-00-860-080
A. Aircraft Maintenance Configuration
(1)
Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).
(2)
Do the ADIRS start procedure (Ref. TASK 34-10-00-860-002).
(3)
On the center pedestal, on the ATC/TCAS control unit, set:
-
the ATC system 1(2) on.
-
the ALT RPTG ON/OFF switch to ON.
-
the AUTO/ON/STBY switch to AUTO.
1EFF : ALL 1 34-52-00Page 505 1 1 Feb 01/04R 1 1 1CES 1
Subtask 34-52-00-865-054
B. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU COM NAV/ATC/1 5SH1 G11 121VU COM NAV/ATC/2 5SH2 K07
4. Procedure
_________
Subtask 34-52-00-710-055
A. Transmission Test
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
On the ATC/TCAS control unit:
-
set the AUTO ON/STBY switch to ON. On the ATC/TCAS control unit:
-the ATC FAULT or FAIL indicator light stays off.
-
set the AUTO ON/STBY switch to On the ATC/TCAS control unit:
STBY. - the display stays on.
R
5. Close-up
________
Subtask 34-52-00-860-062
A. Put the aircraft back to its initial configuration.
(1)
Do the ADIRS Stop Procedure (Ref. TASK 34-10-00-860-005).
(2)
De-energize the aircraft electrical circuits
(Ref. TASK 24-41-00-862-002).
(3)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : ALL 1 34-52-00Page 506 1 1 May 01/04 1 1 1CES 1
TASK 34-52-00-720-004 Functional Test of the Altitude Reporting Function NOTE : You must do this test very quickly to prevent interference with air
____ traffic, specially if the aircraft is in the open air. If the test is long you must tell the nearest airport of this test.
1. Reason for the Job
__________________
Refer to the MPD TASK: 345200-01
Functional Test of the Altitude Reporting Function.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific ATC ground test unit
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied
from the External Power 34-10-00-860-002 ADIRS Start Procedure 34-10-00-860-005 ADIRS Stop Procedure 34-13-00-710-004 Operational Test of the ALT DYNAMIC SLEW TEST
3. Job Set-up
__________ Subtask 34-52-00-860-088
A. Aircraft Maintenance Configuration
(1)
Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).
(2)
Do the ADIRS start procedure (Ref. TASK 34-10-00-860-002).
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NAVIGATION 導(dǎo)航4(126)
