3. Job Set-up
__________ R **ON A/C 001-049, 051-099, 101-105, 151-199,
 Subtask 34-53-00-860-053
 A. Aircraft Maintenance Configuration
 (1)
 Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).

 (2)
 Do the ADIRS start procedure (Ref. TASK 34-10-00-860-002).

 1EFF : ALL 1 34-53-00Page 501 1 1 May 01/05 1 1 1CES 1

 (3)
 Do the IR alignment procedure
 (Ref. TASK 34-10-00-860-004).

 (4)
 On the EFIS control sections of the FCU:

 -
set the ADF/VOR selector switches to ADF

 -
set the mode selector switches to ROSE/NAV.

 (5)
 On the center pedestal, on the MCDU:

 -get the SYSTEM REPORT/TEST/NAV page
 (Ref. TASK 31-32-00-860-010)

 -push the NEXT PAGE function key.

 (6)
 On the center pedestal, on the RMP1 (RMP2):

 -set the ON/OFF switch to ON
 -push the NAV pushbutton switch (the green LED on this pushbutton switch comes on)
 -tune ADF1 and ADF2 to a non local station (frequency more than 750 KHz). (Ref. Fig. 501/TASK 34-53-00-991-002)

R **ON A/C 106-149, 201-299, 301-399, 401-499,
 Subtask 34-53-00-860-053-A
 A. Aircraft Maintenance Configuration
 (1)
 Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).

 (2)
 Do the ADIRS start procedure (Ref. TASK 34-10-00-860-002).

 (3)
 Do the IR alignment procedure
 (Ref. TASK 34-10-00-860-004).

 (4)
 On the EFIS control sections of the FCU:

 -
set the ADF/VOR selector switches to ADF.

 -
set the mode selector switches to ROSE/NAV.

 (5)
 On the center pedestal, on the MCDU:

 -get the SYSTEM REPORT/TEST/NAV page
 (Ref. TASK 31-32-00-860-010)

 -push the NEXT PAGE function key.
 1EFF : ALL 1 34-53-00Page 502 1 1 Aug 01/05 1 1 1CES 1

 ADF-Frequency Selection
 Figure 501/TASK 34-53-00-991-002
 1EFF :  ALL  1  34-53-00 Page 503 
1  1  Feb 01/98
 1  1
 1CES  1

 (6)
 On the center pedestal, on the RMP1 (RMP2):

 -set the ON/OFF switch to ON
 -push the NAV pushbutton switch (the green LED on this pushbutton switch comes on)
 -tune ADF1 and ADF2 to a non local station (frequency more than 750 KHz). (Ref. Fig. 501/TASK 34-53-00-991-002)

 (7)
 On the VOR/ADF/DME RMI:

 -set the VOR/ADF selector switches to ADF.
 **ON A/C ALL
 Subtask 34-53-00-865-055
 B. Make sure that this(these) circuit breaker(s) is(are) closed:
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU NAV/VOR/DME/RMI 12FN F13 49VU NAV/ADF/1 1RP1 H14 121VU COM NAV/ADF/2 1RP2 K02
 4. Procedure
_________

R **ON A/C 001-049, 051-051, 053-099, 101-105, 151-199,
 Subtask 34-53-00-740-050
 A. BITE Test of the ADF
 NOTE : During the BITE TEST (ADF1 or 2) by the MCDU, the indications
____ related to the two receivers (Capt and F/O) are shown at the same time.This has no effect on the test or component.
 1EFF : ALL 1 34-53-00Page 504 1 1 May 01/05 1 1 1CES 1

 -------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
1. On the MCDU:  On the MCDU:
 - push the line key adjacent to the ADF1 (ADF2) indication. - the ADF1 (ADF2) page comes into view.
 - push the line key adjacent to the TEST indication.  - the INITIAL CONDITIONS are shown(page 1 to 3).
 - push the line key adjacent to the START TEST indication.  - the TEST IN PROGRESS 13S indicationcomes into view.
 From 0 to 6s: - On the CAPT and F/O NDs: * the ADF1 (ADF2) pointer dissapears. * the RED ADF1 (ADF2) warning message comes into view.
 From 6 to 13s: - On the CAPT and F/O NDs: * the ADF1 (ADF2) pointer comes into view, moves to a relative bearing of 135..
 On the MCDU:  On the MCDU:
 - push the line key adjacent to the YES indication. the TEST OK indication comes into view.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NAVIGATION 導航4(152)