-
The AIDS page comes into view.
-
The indication *RUN changes into RUN.
-
The indication STOP changes into STOP*.
On the DAR display:
-
The message 0 ADVISORIES comes into view.
-
The message 1 ACQUISITION comes into view.
R 1EFF : 151-199, 201-210, 1 31-36-00Page 514 1 1 May 01/05 1 1 1CES 1
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
-Push the SET pushbutton. - The message RAW:XXXXX/XXXXX (number of the acquired/recorded subframes) comes into view and the number increases one time per second.
-Close the recorder front access
door.
4. On the MCDU: On the MCDU display:
-Push the line key adjacent to - The indication RUN changes into *RUN.
the STOP* indication. - The indication STOP* changes into STOP.
NOTE : The recorder is now in a serviceable condition.
____ R **ON A/C 106-149, 151-199, 201-299, 301-399, 401-499,
5. Close-up
________
Subtask 31-36-00-410-053
A. Close Access
(1)
On the MCDU, push the line key adjacent to the RETURN indication until the CFDS menu page comes into view.
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
(3)
Close the access door 824. (Ref. TASK 52-41-00-410-002)
(4)
Remove the access platform(s).
Subtask 31-36-00-862-054
B.
De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002)
R 1EFF : 106-149, 151-199, 201-299, 301-399, 1 31-36-00Page 515 1401-499, 1Aug 01/05 1 1 1CES 1
MANAGEMENT UNIT - DATA (DMU OR FDIMU) (1TV,10TV) - REMOVAL/INSTALLATION
_______________________________________________________________________ **ON A/C 001-049, 051-099, 101-105, 151-199, 201-210,
TASK 31-36-34-000-001
Removal of the Data Management Unit (DMU) (1TV)
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific access platform 1.6 m (5 ft. 3 in.)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
31-36-00-740-006 Printout of the APU Hours and Cycles
31-36-00-740-007 Printout of the Engine Hours and Cycles
R **ON A/C 001-049, 051-099, 101-105, 151-158, 201-209,
31-36-34-991-001 Fig. 401
1EFF : ALL 1 31-36-34Page 401 1 1 Config-1 Aug 01/05 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-210,
3. Job Set-up
__________
Subtask 31-36-34-740-052
A. Print out the APU hours and cycles (Ref. TASK 31-36-00-740-006) and the Engine hours and cycles (Ref. TASK 31-36-00-740-007)
Subtask 31-36-34-865-050
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
121VU AIDS/DMU 4TV K15
Subtask 31-36-34-010-050
C. Get Access
(1)
Put the access platform in position in zone 128, at the access door
824.
(2)
Open the access door 824.
4. Procedure
_________ R **ON A/C 001-049, 051-099, 101-105, 151-158, 201-209,
(Ref. Fig. 401/TASK 31-36-34-991-001)
**ON A/C 001-049, 101-105,
Subtask 31-36-34-550-053
A. On the DMU front face, set the OPERATING/STORAGE switch to STORAGE.
1EFF : 001-049, 051-099, 101-105, 151-199, 1 31-36-34Page 402 1201-210, 1Config-1 Aug 01/05 1 1 1CES 1
Data Management Unit (DMU)
Figure 401/TASK 31-36-34-991-001
R 1EFF : 001-049, 051-099, 101-105, 151-158, 1 31-36-34Page 403 1201-209, 1Config-1 Aug 01/05 1 1 1CES 1 **ON A/C 001-049, 051-099, 101-105, 151-199, 201-210, 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM 指示/記錄系統 4(30)
