R CMM 31-35-99
 3. Job Set-up
__________
 Subtask 31-33-00-861-061
 A. Energize the aircraft electrical circuits
 (Ref. TASK 24-41-00-861-002).

R 1EFF : 001-049, 051-099, 101-105, 1 31-33-00Page 212 1 1 May 01/05 1 1 1CES 1

 Subtask 31-33-00-010-055
 B. Get Access
 (1) Put the access platform in position at the access door 811.
 (2) Open the access door 811. (Ref. TASK 52-41-00-010-002)
 Subtask 31-33-00-865-071
 C. Make sure that this(these) circuit breaker(s) is(are) closed:
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU RCDR/ACCLRM 9TU K18 121VU FDIU & QAR 8TU K17
 4. Procedure_________ 
R  **ON A/C 051-099, 
R  Subtask 31-33-00-710-066-A 
R  A. Software Load Procedure 
R  (1) Do the optical QAR Software Load Procedure (Ref. CMM 31-35-99). 

R 1EFF : 001-049, 051-099, 101-105, 1 31-33-00Page 213 1 1 May 01/05 1 1 1CES 1

R  **ON A/C 001-049, 101-105,
 Subtask 31-33-00-710-073 
R  B. Do the Optical QAR Software Load Procedure
 NOTE : The messages XXXXX, XXXXXXXX and VX.X on the OQAR display in this____ procedure is each X written for a hex number.
 -------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------

1. On the QAR:
-Open the recorder access door.
 -If a data disk installed in the disk drive push the EJECT button.
-Put the Bootable Application Disk into the disk drive and immediately push and hold the SET button.
-If the message **BAD DISK does not comes on, push and hold the SET button, + button and -button at the same time.
 -Continue hold down the SET button and release the + button and the - button.
On the QAR:
On the display:
-While the disk ejects the messageEJECTING comes into view.
 -After the disk ejects the message INSERT DISK comes into view.
On the display:
-The message **BAD DISK comes intoview.
-After approximately 1 minute the message BOOTABLE OPTICAL comes into view.
On the display:
-After approximately 1 minute themessage BOOTABLE OPTICAL comes into view.
 NOTE : If the message ** BAD DISK does not comes on, alternate you can
____ de-energize the OQAR from the electrical power for 5 seconds. While re-energizing the SET button must be pushed.
R 1EFF : 001-049, 101-105, 1 31-33-00Page 214 1 1 May 01/05 1 1 1CES 1

 -------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
-After the message BOOTABLE  On the display: OPTICAL comes into view, - The message FEPROM VX.X comes into release the SET button. view.
 -After approximately 2 minutes the massage PREERASE XXXXX comes into view.
 NOTE : The message PREERASE with a hex number shows and the hex number
____ decrements from 80000 to 0000. Then then message ERASE with a hex number shows and the hex number decrements from 80000 to 0000. At least it shows the message WRITE and the hex number decrements from
 80000 to 0000.
 On the display: - After approximately 30 minutes the message SUM XXXXXXXX OK? comes into view.
 - Push the SET push button.  On the disk drive: - The Bootable Application Disk ejects.
 On the display: - The message INSERT DISK comes into view.
 - Put a Data Disk into the disk drive.  On the display:- While the disk drive initiates the
 data disk the message DISK DETECTED comes into view.
 - After the disk drive has the data
 disk initiated the message OQAR READY comes into view.
 - Push the MODE button to get access to the main menu.
 - Push the + or - button until the S/W VERSION indicates on the display.  On the display:- The message S/W VERSION comes intoview.
 - Push the SET button.  On the display: - The software Partnumber and Version
 indicates. 

R 1EFF : 001-049, 101-105, 1 31-33-00Page 215 1 1 May 01/05 1 1 1CES 1

 -------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
-Make sure, that the Partnumber and Version are correct.
 -
Push the MODE button to get access to the main menu.

 -
Push the + or - button until DIAGNOSTIC indicates on the display.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 指示/記錄系統 2(75)