A. Removal of the Safety Device
(Ref. Fig. 203/TASK 29-22-00-991-004)
(1)
Loosen the screw (3) and remove the thrust block (4).
(2)
Remove the safety block (5)SAFETY DEVICE - RAT (98D29207542000).
5. Close-up
________
Subtask 29-22-00-865-085
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 2801GE, 2803GE, 6XE
R 1EFF : 001-049, 051-061, 101-105, 201-203, 1 29-22-00Page 228 1 1 Config-1 May 01/05 1 1 1CES 1 Subtask 29-22-00-410-067
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the access door 195BB.
(3)
Remove the warning notice(s).
R 1EFF : 001-049, 051-061, 101-105, 201-203, 1 29-22-00Page 229 1 1 Config-1 May 01/05 1 1 1CES 1R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
TASK 29-22-00-860-007
Installation of the Safety Device of the Ram Air Turbine
WARNING : MAKE SURE THAT THE RAT TRAVEL RANGE IS CLEAR BEFORE YOU
_______
EXTEND/RETRACT THE RAT.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
To prevent accidental deployment of the Ram Air Turbine (RAT).
When you work near the RAT, you must install the safety device.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific warning notices
98D29208246001 1 SAFETY DEVICE - RAT
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-22-00-991-020 Fig. 204
3. Job Set-up
__________
Subtask 29-22-00-941-082
A. Put the warning notices in position to tell persons not to operate the RAT: - on the overhead panels 21VU and 40VU.
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 29-22-00Page 230 1301-399, 401-499, 1Config-1 Aug 01/05 1 1 1CES 1 Subtask 29-22-00-865-104
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU HYD/RAT/CTL 2801GE D14 106VU CSM/G /EV/MAN/SPLY 6XE B04 121VU HYDRAULIC/RAT/SPLY/EXTN/SOL1 2803GE P33
Subtask 29-22-00-010-078
C. Open the access door 195BB.
4. Procedure
_________ Subtask 29-22-00-481-053
A. Installation of the Safety Device
(Ref. Fig. 204/TASK 29-22-00-991-020)
(1)
Put the SAFETY DEVICE - RAT (98D29208246001) (6) in position between the RAT (1) and the structure (2).
(2)
Move the thrust piece (7) apart so that the ends of the SAFETY DEVICE
-RAT (98D29208246001) (6) are on the structure (2).
(3)
Tighten the cross handle (3) to keep the SAFETY DEVICE - RAT (98D29208246001) in position.
CAUTION : TO PREVENT A LIFT UP OF THE RAT, MAKE SURE THAT THE THRUST
_______ PLATE DOES NOT COME INTO CONTACT WITH THE RAT.
(4)
Turn the cross handle (4) in the clockwise direction until there is clearance of at least 1 mm (0.0393 in.) between the thrust plate (8) and the RAT (1).
(5)
Make sure that the signal flag (5) hangs outside of the aircraft so that you can see it.
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 29-22-00Page 231 1301-399, 401-499, 1Config-1 Aug 01/05 1 1 1CES 1
RAT Safety Device
Figure 204/TASK 29-22-00-991-020
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 29-22-00Page 232 1301-399, 401-499, 1Config-1 Aug 01/05 1 1 1CES 1
TASK 29-22-00-860-008 Removal of the Safety Device of the Ram Air Turbine WARNING : MAKE SURE THAT THE RAT TRAVEL RANGE IS CLEAR BEFORE YOU
_______ EXTEND/RETRACT THE RAT.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM HYDRAULIC POWER 液壓5(112)
