曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  A. Preparation for Installation 
R  WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______ 
R  MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. 
R  OBEY THE MANUFACTURERS INSTRUCTIONS. 
R  PUT ON PROTECTIVE CLOTHING. 
R  DO NOT GET THEM IN YOUR MOUTH. 
R  DO NOT SMOKE. 
R  DO NOT BREATHE THE GAS. 
R  THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. 
R  GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED. 
R  (1) Clean the component interface and/or the adjacent area with 
R  MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS 
R  (Material No. 11-004). 
R  (2) Do an inspection of the component interface and/or the adjacent area. 
R  (3) Make sure that the parts retained from the removed component are 
R  clean and in the correct condition.

 

R  (4) Apply FUELS (Material No. 01-001) or COMMON GREASE (Material No. 04-
R  012) to: 
R  - FOR 202QM 
R  the new O-ring (4) and new O-ring (5) 
R  - FOR 203QM 
R  the new O-ring (4) and the O-ring (5). 
R  (5) Install the O-ring (5) on to the base (2) 
R  Subtask 28-43-22-420-055 
R  B. Installation of the Magnetic-Level-Indicator Assembly 202QM (203QM) 
R  (1) Apply a thin layer of SEALANTS (Material No. 09-001) to the interface 
R  of the bolts (6) 
R  (2) Install the bolts (6), the O-rings (4), the MLI (7) and the nuts (3). 
R  (3) Apply a thin layer of SEALANTS (Material No. 09-001) over the nuts 
R  (3) and the bolts (6). 
R  (4) Make sure the float (1) moves smoothly along the complete length of 
R  the MLI tube. 
R  Subtask 28-43-22-410-051 
R  C. Close Access 
R  (1) Make sure that the work area is clean and clear of tool(s) and other 
R  items. 
R  (2) Install the access panel (Ref. TASK 57-27-11-400-002): 
R  - FOR 202QM 
R  install 540QB 
R  - FOR 203QM 
R  install 640QB. 
R  Subtask 28-43-22-650-053 
R  D. Fuel Configuration 
R  (1) Refuel, defuel or transfer fuel as necessary (Ref. TASK 12-11-28-650-
R  003), (Ref. TASK 28-25-00-650-001) or (Ref. TASK 28-25-00-869-001)

 

R  Subtask 28-43-22-790-051 
R  E. Test 
R  (1) Make sure that fuel does not leak from the MLI assembly (7). 
R  5. Close-up________ 
R  Subtask 28-43-22-942-053 
R  A. Removal of Equipment 
R  (1) Remove the safety barriers. 
R  (2) Remove the access platform(s). 
R  (3) Remove the ground support and maintenance equipment, the special and 
R  standard tools and all other items.

 

 INDICATOR - MAGNETIC LEVEL (91QM,92QM,98QM) - REMOVAL/INSTALLATION
__________________________________________________________________ TASK 28-43-23-000-001 Removal of the Magnetic Level-Indicator Rod 92QM. WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
28-00-00-910-001 Fuel Safety Procedures 28-43-23-991-001 Fig. 401
 1EFF : ALL 1 28-43-23Page 401 1 1 Feb 01/98 1 1 1CES 1

 3. Job Set-up
__________
 (Ref. Fig. 401/TASK 28-43-23-991-001) Subtask 28-43-23-941-057
 A. Safety Precautions
 WARNING : OBEY THE FUEL SAFETY PROCEDURES.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUEL 燃油6(60)