(10)
 Connect the center tank harness 18QT:

 (a)
 Identify the cable ends for the probes 35QT and 39QT and connect them to the correct terminals (Ref. TASK 28-42-15-400-004), (Ref. TASK 28-42-15-000-002).

 (b)
 Identify the cable ends for the sensor 22QJ and connect them to the correct terminals (Ref. TASK 28-46-15-400-012).

 (11)
 Install the O-ring (17) on the electrical backshell (21).

 (12)
 Install the electrical backshell (21) in the applicable position.

 (13)
 Install the washer (18) and the nut (19).

 (14)
 TORQUE the nut (19) to between 9.6 and 10.7 m.daN (70.79 and 78.90 lbf.ft).

 (15)
 Safety the nut (19) to the nut on the adjacent electrical backshell with MISCELLANEOUS (Material No. 19-010).

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-42-44Page 454 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1

 (16)
 Apply SEALANTS (Material No. 09-001) around the electrical backshell

 (21) to seal it to the tank wall.

 (17)
 Connect the fused adapter (24) to the electrical backshell (21).

 (18) Connect the electrical connector (20) to the fused adapter (24). **ON A/C ALL
 Subtask 28-42-44-865-053
 C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1QL, 2QL, 3QL, 1QT, 2QT, 8QT.
 Subtask 28-42-44-410-053
 D. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Close the MLG doors (Ref. TASK 32-12-00-410-001).

 (3)
 Install the applicable cover(s) 147AZ (148AZ) (Ref. TASK 57-17-11-400-001).

 Subtask 28-42-44-740-053
 E. Test
 (1)
 Do a status report (BITE) of the fuel-quantity indicating system (Ref. TASK 28-42-00-740-001).

 (2)
 Do a functional (BITE) test of the fuel-tank level-sensing system (Ref. TASK 28-46-00-740-001).

 5. Close-up
________ Subtask 28-42-44-942-054
 A. Removal of Equipment
 (1)
 Remove the safety barriers.

 (2)
 Remove the warning notice(s).

R 1EFF : ALL 1 28-42-44Page 455 1 1 May 01/05 1 1 1CES 1

 (3)
 Remove the access platform(s).

 (4)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 1EFF : ALL 1 28-42-44Page 456 1 1 May 01/05R 1 1 1CES 1

R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 TASK 28-42-44-000-003
 Removal of the Center Tank Fuel Quantity Indicating Probe Fused Adapters
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
 No specific circuit breaker(s) safety clip(s)
 No specific safety barriers
 No specific warning notice
 No specific access platform 3 m (9 ft. 10 in.)

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-42-44Page 457 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1

 B. Referenced Information -------------------------------------------------------------------------------
REFERENCE DESIGNATION -------------------------------------------------------------------------------32-12-00-010-001 Open the Main Gear Doors for Access
R  **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499, Post SB 28-1087 For A/C 001-049,051-061,101-105,201-203, 28-42-44-991-006 Fig. 403

R  **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 3. Job Set-up
__________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499, Post SB 28-1087 For A/C 001-049,051-061,101-105,201-203, (Ref. Fig. 403/TASK 28-42-44-991-006) Subtask 28-42-44-941-055
 A. Safety Precautions
 (1)
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUEL 燃油6(30)