-
harness (25) is not caught between the edge of the rear fairing

 (16) and the wing skin.
 (i) Make sure that there is a clearance of 3.0 mm (0.1181 in.) to 4.0 mm (0.1574 in.) between the rear fairing (16) and the intermediate fairing (17). If necessary, cut and de-burr the overlap at the rear of the intermediate fairing (17) to get the correct dimension.
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 28-21-49Page 450 1201-227, 1May 01/05 1 1 1CES 1

 (j)
 Install the bolt (15), the bush (14) and the nut (13). Tighten the bolt (15).

 (k)
 Fill the clearance between the rear fairing (16) and intermediate fairing (17) with SEALANTS (Material No. 09-016).

 (5) Install the front fairing (20) and the cover plate (22) assembly as follows:
 (a)
 Make sure that the intermediate fairing (17) and the rear fairing

 (16)
 are correctly installed.

 (b)
 If the front fairing (20) and the cover plate (22) have been disassembled, continue as follows:

 1 Loosely assemble the front fairing (20) to the cover plate
_
 (22) with the bolt (24), the washer (23) and the bush (18). 2 Loosely assemble the cover plate (22) complete with the front
_ fairing (20) to the wing skin with the bolts (21).
 3 Make sure that the front fairing (20) aligns with the
_ intermediate fairing (17).
 4 Use a wax crayon to mark on the cover plate (22) around the
_ edge of the front fairing (20).
 5 Remove the bolts (21) and remove the cover plate (22),
_ complete with the front fairing (20).
 6 Remove the bolt (24), the washer (23) and the bush (18).
_ Remove the front fairing (20) from the cover plate (22).
 7 Apply SPECIAL MATERIALS (Material No. 05-064) to the mating
_ surface of the front fairing (20). Do not apply the special material to the surface of the front fairing that will touch the wing skin.
 8 Apply a small quantity of SEALANTS (Material No. 09-018) to
_ the mating surfaces of the front fairing (20) and the cover plate (22). Do not apply sealant to the surface of the front fairing that will touch the wing skin.
 9 Install the front fairing (20) onto the cover plate (22) with
_ the bolt (24), the washer (23) and the bush (18). Make sure that the front fairing (20) aligns with the marks you made on the cover plate (22).
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 28-21-49Page 451 1201-227, 1May 01/05 1 1 1CES 1

 10__ TORQUE tighten the bolt (24) to between 0.08 and 0.10 m.daN
 (7.07 and 8.84 lbf.in).
 NOTE : Do the step that follows before the sealant has cured.____
 11__ Use the sealant pushed out from between the front fairing (20)
 and the cover plate (22) to make a fillet seal. Clean the
 unwanted sealant from the front fairing and the cover plate
 assembly to make a smooth finish. Make sure that the sealant
 does not cause a blockage in the drain hole (19).

 (c) Hold the front fairing (20) and the cover plate (22) assembly in position against the wing skin.
 NOTE : Make sure that the harness (25) does not rub against the
____ edges of the cover plate (22).
 (d)
 Make sure that there is a clearance of 0.5 mm (0.0196 in.) to 3.0 mm (0.1181 in.) between the intermediate fairing (17) and the front fairing (20). If necessary, cut and de-burr the overlap at the rear of the front fairing (20) to get the correct dimension.

 (e)
 Install the assembly with the bolts (21).

 (f)
 TORQUE tighten the bolts (21) to 1.13 m.daN (99.99 lbf.in).

 (6) Make sure that the guide (30), the bracket (34) and the clamp (33) are positioned correctly. TORQUE the nuts (31) on the bolts (32) to between 0.14 and 0.16 m.daN (12.38 and 14.15 lbf.in).
 **ON A/C ALL
 5. Close-up
________ Subtask 28-21-49-410-050
 A. Removal of Equipment
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Close the applicable MLG door (Ref. TASK 32-12-00-410-001).

 (3)
 Remove the access platform(s).

 (4)
 Remove the safety barriers.

R 1EFF : ALL 1 28-21-49Page 452 1 1 May 01/05 1 1 1CES 1

 (5) Remove the warning notice(s).

R 1EFF : ALL 1 28-21-49Page 453 1 1 May 01/05 1 1 1CES 1R PUMP - FUEL (21QA,22QA,25QA,26QA,37QA,38QA) - REMOVAL/INSTALLATION

__________________________________________________________________
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUEL 燃油3(60)