(3) Install the intermediate fairing (5) as follows:
 (a)
 Hold the intermediate fairing (5) in position near the lower wing skin.

 (b)
 Carefully push the harness (25) into the retention channel inside the intermediate fairing (5).

 (c)
 Make sure that the harness (25) is held correctly below the lips of the retention channel in the intermediate fairing (5).

 NOTE : Make sure that the harness (25) is not in tension.
____
 (d)
 Engage the key-hole slots in the intermediate fairing (5) with the wing skin bolts.

 (e)
 Move the intermediate fairing (5) forward to engage the bolts fully.

 (f)
 Make sure that the harness (25) is not caught between:

 -
the key-hole slot positions on the intermediate fairing (5) and the wing skin

 -
the edge of the intermediate fairing (5) and the wing skin.

 (4) Install the rear fairing (4) as follows:
 (a)
 Make sure that the intermediate fairing (5) is correctly
 installed and pushed tightly against its stop.

 (b)
 Hold the rear fairing (4) in position near the wing skin.

 (c)
 Carefully push the harness (25) into the retention channel inside the rear fairing (4).

 (d)
 Make sure that the harness (25) is held correctly below the lips of the retention channel in the rear fairing (4).

 NOTE : Make sure that the harness (25) is not in tension.
____
 (e) Pull the harness (25) lightly in a rearwards direction. If necessary, push unwanted harness (25) up through the guide (30) and the clamp (33) into the conduit (35).
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 28-21-49Page 446 1201-227, 1May 01/05 1 1 1CES 1

 (f)
 Engage the key-hole slots in the rear fairing (4) with the wing skin bolts.

 (g)
 Move the rear fairing (4) forward to engage the bolts fully.

 (h)
 Make sure that the:

 -forward end of the rear fairing (4) goes inside the intermediate fairing (5) (out-of-wind)
 -
harness (25) is not caught between the key-hole slot positions on the rear fairing (4) and the wing skin

 -
harness (25) is not caught between the edge of the rear fairing

 (4) and the skin.
 (i)
 Make sure that there is a clearance of 3.0 mm (0.1181 in.) to 4.0 mm (0.1574 in.) between the rear fairing (4) and the intermediate fairing (5). If necessary, cut and de-burr the overlap at the rear of the intermediate fairing (5) to get the correct dimension.

 (j)
 Install the bolt (3), the bush (2) and the nut (1). Tighten the bolt (3).

 (k)
 Fill the clearance between the rear fairing (4) and intermediate fairing (5) with SEALANTS (Material No. 09-016).

 (5) Install the front fairing (8) and the cover plate (10) assembly as follows:
 (a)
 Make sure that the intermediate fairing (5) and rear fairing (4) are correctly installed.

 (b)
 If the front fairing (8) and the cover plate (10) have been disassembled, continue as follows:

 1_ Install the front fairing (8) to the cover plate (10) with the
 bolt (12), the washer (11) and the bush (6). Do not tighten
 the bolt (12)
 2_ Install the cover plate (10), complete with the front fairing
 (8) to the lower wing with the bolts (9). Do not tighten the
 bolts (9).
 3_ Make sure that the front fairing (8) aligns correctly with the
 intermediate fairing (5).
 4_ Use a wax crayon to mark on the cover plate (10) around the
 edge of the front fairing (8). 

R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 28-21-49Page 447 1201-227, 1May 01/05 1 1 1CES 1

 5 Remove the bolts (9) and remove the cover plate (10), complete
_ with the front fairing (8).
 6 Remove the bolt (12), the washer (11) and the bush (6). Remove
_
 the front fairing (8) from the cover plate (10).

 7 Apply SPECIAL MATERIALS (Material No. 05-064) to the mating
_ surface of the front fairing (8). Do not apply the special material to the surface of the front fairing that will touch the wing skin.
 8 Apply a small quantity of SEALANTS (Material No. 09-018) to
_ the mating surfaces of the front fairing (8) and the cover plate (10). Do not apply sealant to the surface of the front fairing that will touch the wing skin.
 9 Install the front fairing (8) onto the cover plate (10) with
_ the bolt (12), the washer (11) and the bush (6). Make sure that the front fairing (8) aligns with the marks you made on the cover plate (10).
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM FUEL 燃油3(58)