(21)
Lift the LIFTING FRAME ASSEMBLY (AILERON) with the crane. Put the LIFTING FRAME ASSEMBLY (AILERON) around the aileron, at the same distance from each end.
NOTE : The weight of the aileron and the brackets is 50 kg (110.2311
____
lb).
(22) To lock the lifting frame assembly: CAUTION : DO NOT TIGHTEN THE ADJUSTER ASSEMBLIES ON THE LIFTING FRAME
_______
TOO MUCH OR YOU WILL DAMAGE THE AILERON.
(a) Tighten the adjuster assemblies to lock the LIFTING FRAME ASSEMBLY (AILERON) in position.
(23)
For hinge No.s 1, 2 and 3:
(a)
Remove the nut (75), the bolt (84), the washers (76) and (83), and the bonding strap (77).
(b)
Remove the nut (74), the bolt (73) and the locking plate (72).
(24)
For hinge No.s 2 and 3:
(a)
Remove and discard the cotter pin (82) from the locking cap (81).
(b)
Remove the locking cap (81), the nut (80) and the washer (79).
(25)
For hinge No. 5 only, remove the nut (106), the bolt (97), the washers (98) and (105), and the bonding strap (99).
R 1EFF : 001-003, 051-052, 1 27-14-41Page 414 1 1 May 01/05 1 1 1CES 1
(26)
For hinge No.s 4 and 5, do the steps that follow:
(a)
Remove the nut (107), the bolt (95), the washers (96) and (108), and the bonding strap (90).
(b)
Remove the bolt (94) and the locking plate (93).
(c)
Remove and discard the cotter pin (104) from the locking cap (103).
(d)
Remove the locking cap (103), the nut (102) and the washer (101).
(27)
Make sure that the aileron is supported by the crane and remove the hinge pins (71) and (92). Move the aileron aft and away from the wing and put it on the trestle.
(28)
If the aileron is to be replaced, loosen the adjuster assemblies and remove the LIFTING FRAME ASSEMBLY (AILERON) from the aileron.
Subtask 27-14-41-020-052-B
B. Removal of the Bushes from the Hinges If the aileron is safetied with STA-LOK nuts, do the steps that follow:
(1)
For the hinge No. 1, remove the bush (26).
(2)
For the hinge No.s 2 and 3, remove the bushes (18) and (26).
(3) For the hinge No.s 4 and 5, remove the bushes (41) and (50). If the aileron is safetied with ABS 0738 nuts, do the steps that follow:
(4)
For the hinge No. 1, remove the bush (78).
(5)
For the hinge No.s 2 and 3, remove the bushes (70) and (78).
(6)
For the hinge No.s 4 and 5, remove the bushes (91) and (100).
R 1EFF : 001-003, 051-052, 1 27-14-41Page 415 1 1 May 01/05 1 1 1CES 1R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 27-14-41-020-053-A
A. Removal of the Aileron
(1)
Remove the nuts (61), the washers (60), the bolts (69) and the locking plates (68).
(2)
Remove and discard the cotter pins (65) from the locking caps (64).
(3)
Remove the locking caps (64), the nuts (63) and the washers (62).
(4)
Hold the aileron and remove the pins (67).
(5)
Manually retract the actuators No. 1 and No. 2 and remove the flanged bushes (66) from the actuator attachment brackets.
(6)
Manually move the aileron to the highest position.
(7)
Install the LIFTING FRAME ASSEMBLY (AILERON) (98D27104001000):
(a)
Make sure that the side plates on the LIFTING FRAME ASSEMBLY (AILERON) are correctly installed.
(b)
Make sure that the adjuster assemblies on the LIFTING FRAME ASSEMBLY (AILERON) are as far apart as possible.
(8)
Lift the LIFTING FRAME ASSEMBLY (AILERON) with the crane. Put the LIFTING FRAME ASSEMBLY (AILERON) around the aileron, at the same distance from each end.
NOTE : The weight of the aileron and the brackets is 50 kg (110.2311
____
lb).
(9) To lock the lifting frame assembly: CAUTION : DO NOT TIGHTEN THE ADJUSTER ASSEMBLIES ON THE LIFTING FRAME
_______ TOO MUCH OR YOU WILL DAMAGE THE AILERON.
(a) Tighten the adjuster assemblies to lock the LIFTING FRAME ASSEMBLY (AILERON) in position.
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 27-14-41Page 416 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(10)
For hinge No.s 1, 2 and 3:
(a)
Remove the nut (75), the bolt (84), the washers (76) and (83), and the bonding strap (77).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱1(89)
