Component Location
 Figure 507A/TASK 27-21-00-991-008-A12 (SHEET 1)

R 1EFF : 106-149, 218-299, 301-399, 401-499, 1 27-21-00Page 550 1 1 Aug 01/05 1 1 1CES 1

 Component Location
 Figure 507A/TASK 27-21-00-991-008-A22 (SHEET 2)

R 1EFF : 106-149, 218-299, 301-399, 401-499, 1 27-21-00Page 551 1 1 Aug 01/05 1 1 1CES 1

 Adjustment Graph Figure 508/TASK 27-21-00-991-009 
R 1EFF : 1 1 1CES  ALL  1 111 27-21-00 Page 552 Aug 01/04

 4_ Measure the length between two marks of each cable
 - if the length is more than 45 mm (1.7716 in.), shorten the
 control cables (Ref. TASK 27-21-00-820-004).
 - if the length is less than 45 mm (1.7716 in.), replace the
 rear control cables (Ref. TASK 27-21-61-000-001) (Ref. TASK
 27-21-61-400-001).

 (9) Install the locking clips (8) on the turnbuckles (9). Connect the control rod (7) between the cable quadrant and the mixer (Ref. TASK 27-21-00-840-001). Make sure that bolts can be installed easily. If not, do these operations:
 (a)
 Cut and remove the lockwire from the nuts of the rod (7).

 (b)
 Loosen the nuts.

 (c)
 Release the lockwashers.

 (d)
 Adjust the length of the rod until you can push the bolts freely.

 (e)
 Engage the lockwashers.

 (f)
 Tighten the nuts.

 (g)
 Make sure that the adjustment is correct.

 (h)
 Safety the nuts with lockwire corrosion resistant steel dia 0.8 mm (0.03 in.)

 (10)
 Remove the PIN - RIGGING (98D27207547000) or RIGGING PIN SET (98D27207516000) (6) from the cable quadrant (5).

 (11)
 Remove the PIN, RIGGING - RUDDER CONTROL (98A27901002000) (2) from the tension regulator (1).

 (12)
 With a tensiometer, measure the tension of each cable, in each cargo compartment, between two static fairleads.

 NOTE : The tension value of the two cables must be 22 +4 -4 daN
____ (49.4579 +8.9923 -8.9923 lbf). If the tension value is not correct, replace the cable tension regulator (1) (Ref. TASK 27-21-45-000-001), (Ref. TASK 27-21-45-400-001).
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 27-21-00Page 553 1201-217, 1May 01/05 1 1 1CES 1R **ON A/C 106-149, 218-299, 301-399, 401-499,

 Subtask 27-21-00-820-053-A
 A. Adjustment of the Cable Linkage Assy
 (1)
 Measure the ambient temperature with a thermometer.

 (2)
 Use the adjustment graph to find the position of the index of the cable tension regulator (1), in relation to the ambient temperature.

 (3)
 Install the BRACKET TENSION REGULATOR-RUDDER CONTROL (98D27203500000)

 (10) on the mark of the flange of the cable tension regulator (1) (access door 811).
 NOTE : This tool is used to align the mark on the cable tension
____ regulator with the related graduation on the fixed scale.
 (4)
 Bend the two cables to the same value and release them quickly. When you release the cables, make sure that the two quadrants of the tension regulator move easily (it must not be caught).

 (5)
 Remove the locking clips (8) from the turnbuckles (9).

 (6)
 Turn the 2 turnbuckles (9) by the same value to adjust the length of the cable loop so that:

 (a)
 Read the value on the fixed scale with a mirror and check that the position of the index of the tension regulator (1) agrees with the values found on the graph.

 (b)
 You can install the locking clips (8) on the turnbuckles (9).

 (c)
 You can easily install and remove the PIN, RIGGING - RUDDER CONTROL (98A27901002000) (2) on the input lever of the cable tension regulator (1).

 (7)
 If you cannot install the PIN, RIGGING - RUDDER CONTROL (98A27901002000) easily, adjust the bolt (4):

 (a)
 If necessary, remove the lockwire from the nuts (3) and discard it.

 (b)
 Loosen the nuts (3) from the cable quadrant (5).

R 1EFF : 106-149, 218-299, 301-399, 401-499, 1 27-21-00Page 554 1 1 Aug 01/05 1 1 1CES 1 (c) Turn the bolts (4) on the cable quadrant (5) so that:

 -The position of the index of the tension regulator (1) agrees with the values found on the graph.
 -You can easily install and remove the PIN, RIGGING - RUDDER CONTROL (98A27901002000) (2) on the input lever of the cable tension regulator (1).
 (d)
 Do a check of the dimensions 22.9 +2 -2 mm (0.9015 +0.0787 -0.0787 in.).

 (e)
 Tighten the nuts (3) on the cable quadrant (5). Do not safety the nuts (3) at this time.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱1(151)