R 1EFF : 001-003, 051-052, 1 27-14-51Page 426 1 1 May 01/05 1 1 1CES 1

 (3)
 For 33CE1(33CE2), install the ASC (21):

 (a)
 Hold the ASC (7.4 kg (16.3142 lb)) in a horizontal position.

 (b)
 Align the body eye-end with the bushes in the flanges of the rear-spar jack-bracket.

 (c)
 Install the pin (19).

 (d)
 Manually move the aileron to the down position. Do this until the piston-rod eye-end and the bushes of the aileron jack-bracket are aligned.

 (e)
 Install the pin (23).

 (4)
 For 33CE3(33CE4), install the ASC (20):

 (a)
 Hold the ASC (7.4 kg (16.3142 lb)) in a horizontal position.

 (b)
 Align the body eye-end with the bushes in the flanges of the rear-spar jack-bracket.

 (c)
 Install the pin (18).

 (d)
 Manually move the aileron to the down position. Do this until the piston-rod eye-end and the bushes of the aileron jack-bracket are aligned.

 (e)
 Install the pin (22).

 (5)
 For easier access to the installed ASC manually, put and hold the aileron in the fully-up position.

 (6)
 Apply COMMON GREASE (Material No. 04-022) to the threads of the pins:

 -
for 33CE1(33CE2), the pins (19) and (23)

 -
for 33CE3(33CE4), the pins (18) and (22).

 If the aileron servo control is safetied with ABS 0738 nuts, do the steps that follow:
 (7) Install the flanged bushes (8) and (10) into the inboard-flanges of the aileron and rear-spar jack-brackets.
R 1EFF : 001-003, 051-052, 1 27-14-51Page 427 1 1 May 01/05 1 1 1CES 1

 (8) Apply a layer of STORAGE PRESERVATION (Material No. 15-007) to the eye-ends of the piston rods on the rounded sides only.
 NOTE : Do not get Material 15-007 on the Servocontrol Spherical
____
 Bearings.

 (9) For 33CE1(33CE2), install the ASC (25):
 (a)
 Hold the ASC (7.4 kg (16.3142 lb)) in a horizontal position.

 (b)
 Align the body eye-end with the bushes in the flanges of the rear-spar jack-bracket.

 (c)
 Install the pin (23).

 (d)
 Manually move the aileron to the down position. Do this until the piston-rod eye-end and the bushes of the aileron jack-bracket are aligned.

 (e)
 Install the pin (27).

 (10)
 For 33CE3(33CE4), install the ASC (24):

 (a)
 Hold the ASC (7.4 kg (16.3142 lb)) in a horizontal position.

 (b)
 Align the body eye-end with the bushes in the flanges of the rear-spar jack-bracket.

 (c)
 Install the pin (22).

 (d)
 Manually move the aileron to the down position. Do this until the piston-rod eye-end and the bushes of the aileron jack-bracket are aligned.

 (e)
 Install the pin (26).

 (11)
 For easier access to the installed ASC manually, put and hold the aileron in the fully-up position.

 (12)
 Apply COMMON GREASE (Material No. 04-022) to the threads of the pins:

 -
for 33CE1(33CE2), the pins (23) and (27)

 -
for 33CE3(33CE4), the pins (22) and (26).

 Subtask 27-14-51-420-058 R C. Complete the Installation of the Aileron Servo Control (ASC)

 If the aileron servo control is safetied with STA-LOK nuts, do the steps that follow:
 (1)
 Install the STA-LOK nuts (5) and (14) and the STA-LOK washers (4) and

 (13)
 as follows (Ref. TASK 20-22-00-400-001):

 (a)
 Install the STA-LOK nuts (5) and (14) with the WRENCHES -NOTCHED, TIGHTENING OF NUTS NSA5454 (SL90-315-7500).

 (b)
 TORQUE the nuts (5) and (14) to between 7.0 and 8.0 m.daN (51.62 and 58.99 lbf.ft).

 (c)
 Install the STA-LOK washers (4) and (13) with the TOOL -INSTALLATION, TAB WASHERS STA-LOK NSA5454 (SL90-313-7500).

 (2)
 For 33CE1(33CE2), do the steps that follow:

 (a)
 At the rear-spar jack-bracket: (Ref. Fig. 401/TASK 27-14-51-991-001)

 (b)
 At the aileron jack-bracket: 1 Put the locking plate (22) on the pin (23).

 1_ Put the locking plate (18) on the pin (19).
 2_ Align the bolt hole in the locking plate (18) with the holes
 in the flanges of the rear-spar jack-bracket.
 3_ Install the bolt (17), the washer (16) and the nut (15).

_ 2 Align the bolt hole in the locking plate (22) with the hole in
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM FLIGHT CONTROLS 飛行操縱1(111)