曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (1) Adjust the two turnbuckles to the dimension 'C' = 30 mm (1.18 in.).
 (2) Find the correct value to cut the cables.
 NOTE : Cut the two rear cables by the same value.____
 (a) Use the adjustment graph to find the position of the index of the tension regulator (1) in relation to the ambient temperature.
 (b) Put marks on the two cables where the cable routing is straight and near the structure.
 (c) In the fuselage between two static fairleads, pull the two cables at the same time until the index of the tension regulator is at the position found on the graph.
 NOTE : Pull the cables down to get the necessary force, and____ measure the cable travel 'Y' along the aircraft axis.
 (d) Measure with the marks (on the cables and on the structure) the cable travel 'Y' on each cable to get the necessary cable length. 
R R  (e) For each cable side, subtract 45 mm (1.7716 in.) from the value measured before. 
R R R  NOTE : 45 mm (1.7716 in.) is the cable penetration into the____ terminal stud of one turnbuckle. 
R R  (f) The value 'X' (to cut the cable) = 'Y' (cable travel) - 45 mm (1.7716 in.).

 

R R R  Example: Measured cable travel 'Y' for each cable Cable penetration into the terminal stud Value 'X' to cut the cable  = 110 mm (4.33 in.) = 45 mm (1.77 in.) = 110 mm - 45 mm = 65 mm (4.33 in. - 1.77 in. = 2.55 in.) 
R  Cut the two rear cables by 65 mm (2.55 in.)
 (3) Use the measured clearance between the turnbuckles and the static fairleads to cut the rear cable junction by the calculated value.
 NOTE : Cut the two rear cables by the same value.____
 (4) Install the new turnbuckles on the cable (Ref. CFM Cable Fabrication Man).
 (5) Do the adjustment of the rudder control-cables length (Ref. TASK 27-21-00-820-002).
 (6) Make sure that the clearances 'A' between the two turnbuckles and the fairleads is minimum 25.4 mm (1.00 in.) along the full travel range of the rudder control.
 (7) Make sure that the distance 'B' between the ends of the turnbuckles in each rudder control cable is minimum 90 mm (3.54 in.) in all the positions.
 (8) Make sure that the turnbuckles are in the adjustment range of 38.2 mm (1.50 in.).
 5. Close-up________
 Subtask 27-21-00-860-068
 A. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.
 (2) Remove the special and standard tools and all other items.

 

 TASK 27-21-00-820-005
 Cutting of the Rear Control Cable of the Rudder
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______ MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
 CAUTION : MAKE SURE THAT THE AIRCRAFT IS IN THE TEMPERATURE CONDITIONS (STABLE
_______ AMBIENT TEMPERATURE) SPECIFIED IN THE AIRCRAFT MAINTENANCE CONFIGURATION PARAGRAPH. CHANGES IN THE TEMPERATURE CAN CAUSE INCORRECT MEASUREMENTS.
 1. Reason for the Job
__________________
 Do this procedure when you install a new rear control cable on the rudder.
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific thermometer No specific warning notice No specific access platforms 2.3 m (7 ft. 7 in.) 98A27901002000 1 PIN, RIGGING - RUDDER CONTROL 98D27207547000 1 PIN - RIGGING
 1EFF : ALL 1 27-21-00Page 565 1 1 Aug 01/04R 1 1 1CES 1

 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
12-33-21-618-001 Pre-conditioning through the LP Ground Connection CFM Cable Fabrication Man
 **ON A/C 001-049, 051-099, 101-105, 151-199, 201-217,
 27-21-00-991-008 Fig. 507 R **ON A/C 106-149, 218-299, 301-399, 401-499,
 27-21-00-991-008-A Fig. 507A R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 27-21-00-991-018 Fig. 511
 **ON A/C 301-399,
 27-21-00-991-018-A Fig. 511A
 **ON A/C ALL
 3. Job Set-up
__________
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱1(154)