-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
In the cabin:
- disconnect the electrical test cable. - all FSB and NS signs go off.
- a double LO-chime is heard from all loudspeakers.
In the cockpit on the ECAM upper display unit:
- the SEAT BELT and NO SMOKING messages go off.
3. In the avionics compartment on the rack 96VU: In the cabin:
- connect an electrical test cable between pin 11A of the connector 12HL-AA and DC ground to simulate low pressure. - all FSB and NS signs come on.
- a double LO-chime is heard from all loudspeakers.
In the cockpit on the ECAM upper display unit:
- the SEAT BELT and NO SMOKING messages come on.
In the cabin:
- disconnect the electrical test cable. - all FSB and NS signs go off.
- a double LO-chime is heard from all loudspeakers.
In the cockpit on the ECAM upper display unit:
- the SEAT BELT and NO SMOKING messages go off.
R 1EFF : 151-199, 1 23-73-00Page C548 1 1 Aug 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------4. In the avionics compartment:
- install the CABIN PRESS 1 controller and the CABIN PRESS 2 controller (Ref. TASK 21-31-34-400-001).
**ON A/C 301-399,
Subtask 23-73-00-710-225-C
R R C. Test of the Passenger Lighted Signs Automatic-Function if a Cabin Decompression occurs.
R R NOTE : All ECAM warnings have to be cleared by pushing the CLR pushbutton____ switch on the ECAM control panel to indicate the NO SMOKING and SEAT BELT message on the ECAM upper display unit. Therefore the circuit breakers 2WW and 3WW have to stay closed through the whole test.
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
- all No Smoking (NS) signs flash for a few seconds and then stay on.
R R R NOTE : When the CIDS is already____ switched on before starting the test procedure, the flashing sequence is finished and the NS signs are steady on.
1. In the avionics compartment:
- remove the CABIN PRESS 1 controller 11HL and the CABIN PRESS 2 controller 12HL (Ref. TASK 21-31-34-000-001).
R R 2. In the avionics compartment, on the rack 95VU: In the cabin:
R 1EFF : 151-199, 301-399, 1 23-73-00Page C549 1 1 Aug 01/05 1 1 1CES 1
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
- connect an electrical test
cable between pin 11A of the
connector 11HL-AA and DC ground
to simulate low pressure.
R
R
R
R
R
R
- disconnect the electrical test
cable.
R
R
R
R
R 3. In the avionics compartment, on
R the rack 96VU:
- connect an electrical test
cable between pin 11A of the
connector 12HL-AA and DC ground
to simulate low pressure.
R
R
-all Fasten Seat Belt (FSB) signsflash for a few seconds and then stayon.
-you hear a LO chime from all loudspeakers.
At all entry areas:
-
the EXIT signs come on.
In the cockpit, on the ECAM upper display unit:
-
the SEAT BELT and NO SMOKING message shows.
In the cabin:
-all FSB signs go off.
At all entry areas:
-
the EXIT signs go off.
In the cockpit, on the ECAM upper display unit:
-
the SEAT BELT and NO SMOKING message goes off.
In the cabin:
-all FSB signs flash for a few secondsand then stay on.
-you hear a LO chime from all loudspeakers.
At all entry areas:
-the EXIT signs come on.
R 1EFF : 301-399, 1 23-73-00Page C550 1 1 Aug 01/05 1 1 1CES 1
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM Communications 通訊4(68)
