R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 23-73-38Page 406 1201-299, 1May 01/05 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-149, 201-299,
Subtask 23-73-38-865-051
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------
PANEL SERVICE IDENT. LOCATION
-------------------------------------------------------------------------------
2000VU PASSENGER READING LIGHT 1LW G02
2000VU PASSENGER READING LIGHT 2LW G03
2000VU PASSENGER READING LIGHT 3LW G04
2000VU PASSENGER READING LIGHT 4LW G05
2000VU PASSENGER READING LIGHT 5LW G06
2000VU PASSENGER READING LIGHT 6LW G07
**ON A/C 151-199,
Subtask 23-73-38-865-053
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------
PANEL SERVICE IDENT. LOCATION
-------------------------------------------------------------------------------
2000VU PASSENGER READING LIGHT 1LW G1
2000VU PASSENGER READING LIGHT 2LW G2
2000VU PASSENGER READING LIGHT 3LW G3
2000VU PASSENGER READING LIGHT 4LW G4
2000VU PASSENGER READING LIGHT 5LW G5
2000VU PASSENGER READING LIGHT 6LW G6
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299,
4. Procedure
_________
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-299,
(Ref. Fig. 401/TASK 23-73-38-991-001)
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 23-73-38Page 407 1201-299, 1May 01/05 1 1 1CES 1 Subtask 23-73-38-560-050
A. Preparation of the Replacement Component
(1)
If necessary, make the electrical cable (6) shorter and install the electrical TERMINAL-CABLE (10) with the CRIMPING DEVICE (AMP169994-1).
(2)
Put the HOUSING (11) over the cable terminal (10) and make sure that the housings engage correctly.
Subtask 23-73-38-420-050
B. Installation of the Power Unit for the Passenger Reading Light
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Install the power unit (2) on the related PSIU (1) with the new plastic RIVET (3)
(4)
Remove the blanking caps from the electrical connectors.
(5)
Make sure that the electrical connectors are clean and in the correct condition.
(6)
Connect the electrical connectors (5) to the reading light (7).
(7)
Connect the electrical connectors (4) to the power unit (2).
(8)
Make sure that the work area is clean and clear of tool(s) and other items.
(9)
Lift the PSIU (1) and engage it in the mounting rail (8).
(10) Install the section-hose (9) with the PULLEY ASSEMBLY - SEALING CORD (98A25207503000) to the mounting rail (8).
NOTE : Make sure that the section-hose is not expanded. Move the
____ pulley assemble forward and rearward to prevent this.
Subtask 23-73-38-865-054
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1LW, 2LW, 3LW, 4LW, 5LW, 6LW.
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 23-73-38Page 408 1201-299, 1May 01/05 1 1 1CES 1
Subtask 23-73-38-710-050
R D. Do the operational test of the passenger reading light-system (Ref. TASK 33-25-00-710-001). **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299,
R 5. Close-up________ **ON A/C 001-049, 051-099, 101-105, 151-199, 201-299,
Subtask 23-73-38-862-050
A. De-energize the ground service network (Ref. TASK 24-42-00-862-001)
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 23-73-38Page 409 1201-299, 1May 01/05 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299,
TASK 23-73-38-960-002
Replacement of the Power Unit Fuses for the Passenger Reading Light
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM Communications 通訊4(117)
