4. Procedure
_________
(Ref. Fig. 401/TASK 23-61-41-991-001) Subtask 23-61-41-420-051
A. Preparation for Installation
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1)
Clean the component interface and the adjacent area with a clean MISCELLANEOUS (Material No. 19-003) and CLEANING AGENTS (Material No. 11-004).
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Make sure that the parts retained from the removed component are clean and in the correct condition.
Subtask 23-61-41-420-050
B. Installation of the Static Discharger
(1) Install the static discharger (1) in the static discharger retainer
(3) and tighten the grub screw (2). Subtask 23-61-41-750-050
C. Test
(1) Do a resistance test between the static discharger (1) and the static discharger retainer (3) (Ref. TASK 23-61-00-200-001).
1EFF : ALL 1 23-61-41Page 406 1 1 Feb 01/98 1 1 1CES 1
5. Close-up
________ Subtask 23-61-41-865-051
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV, 5CC1, 5CC2, 14CC1, 14CC2, 19CE1, 19CE2, 19CE3, 15CE1, 15CE2, 16CE1, 16CE2.
Subtask 23-61-41-942-050
B. Remove the Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safety barriers.
(3)
Remove the access platform(s).
(4)
Remove the warning notice(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 23-61-41Page 407 1 1 Feb 01/98 1 1 1CES 1 RETAINER - STATIC DISCHARGER - REMOVAL/INSTALLATION
___________________________________________________
TASK 23-61-42-000-001
Removal of the Static Discharger Retainer
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
R R Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notice
No specific adjustable access platform 5 m (16 ft. 5 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
23-61-41-000-001 Removal of the Static Discharger
23-61-42-991-002 Fig. 401
23-61-42-991-003 Fig. 402
23-61-42-991-004 Fig. 403
23-61-42-991-005 Fig. 404
23-61-42-991-006 Fig. 405
1EFF : ALL 1 23-61-42Page 401 1 1 May 01/04 1 1 1CES 1
3. Job Set-up
__________
(Ref. Fig. 401/TASK 23-61-42-991-002, 402/TASK 23-61-42-991-003, 403/TASK
23-61-42-991-004, 404/TASK 23-61-42-991-005, 405/TASK 23-61-42-991-006)
Subtask 23-61-42-941-050
A. Safety Precautions
R (1) Put the safety barriers in position.
(2) Put a warning notice in position to tell persons not to operate the flight controls.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM Communications 通訊3(9)
